The rosewood fingerboard on the Kay that I have is pretty thin and I'm considering having the fingerboard replaced with an ebony one. Anyone have an idea i.e. range, that something like this would cost?

If I had a fingerboard, would it be okay to take the board and the bass to a luthier and have them do the replacement or do I have to purchase the fingerboard from them for them to do the work?

Depending on the grade of ebony (price goes up based on apperance) and how much luthiers charge in your area, figure about $350-500 total.

I'm sure most guys could care less if you supply the board, in fact it saves them the hassle of ordering one.

Keep in mind that changing the board will make your bass sound and feel like a whole new instrument. If you don't have bridge adjusters, you may need a new bridge (or have adjusters installed) as the new board will be higher. The idea is to put a thick slab on so it can be planed down over the years as it wears. This also means that the neck will be thicker...it will be very noticeable at first.

A top grade ebony fingerboard and nut, top grade luthier, $850. NYC area.

The latest Lemur catalogue I have lists ebony fingerboards from $206 up to $286, depending on the quality of the ebony. Only your luthier can tell you what the charge to install it would be. Remember that in addition to removing the old fingerboard and nut and installing new ones, your luthier will have to do a complete setup, which will be the most extensive your new fingerboard will ever need.

Brian was dead on when he said it will make your bass feel like a completely different instrument. Whenever I play my plywood these days, it freaks me out to play in the upper positions because the fingerboard is so thin compared to my carved bass. Once you make the adjustment, though, you'll be really glad you did.

DURRL

Hi Phil,

Figure on somewhere between 850 to $1000 for the job. Since you're in Brooklyn, you should go see David Gage in Manhatttan. He'll walk you through an estimate and help you figure out waht to do and at what cost. He's a little pricey, but he's the best.

:)

Thanks for the replies. I've been to David Gage to have my bow rehaired and I've been to Kolsteins to have an endpin and tailpiece wire installed, the bass when I got it originally had the metal tailpiece do-hicky with the two screws. I'm partial to Kolsteins because I like the vibe I got from the place more so than the one that I got at David Gage. I do understand that the bass will feel totally different, but it's something that's got to be done especially for the upper register.

I think I may need to replace my bridge as well. It is adjustable though currently to play with the action that I'm using, the adjusters might be up to the maximum. Is it possible to get new bass feet and keep the top part of the bridge if your bridge is adjustable?

Is there any benefit to having a tailpiece that has tuners on it? If so, what is that benefit?

Thanks guys.

[QUOTE]Originally posted by Phil Smith
" I'm partial to Kolsteins because I like the vibe I got from the place more so than the one that I got at David Gage."

I came away with the same feeling when I first visited their shops. Subsequent visits has only confirmed it. I would rank David Gage and his shop at the top of luthiers right along with Kolsteins.

"Is there any benefit to having a tailpiece that has tuners on it? If so, what is that benefit?"

I have the Kolstein adjustable tail piece and I love it. It masks the wolf tone when playing arco. I don't think that you would find any improvement if you only play pizz.

Mark

$850!!!

Boy am I glad I'm not in NYC.

I've had two fingerboards replaced up here in Boston, one was $400 some years ago (7?) the other was $500 two years ago. Both included other neck work (the $500 job included a reset, the bass had been in a car crash) as well.

Gage, Kolstein, and Arnold Schnitzer are the same distance from my house, time-wise. I wouldn't even dream of not going to Arnold Schnitzer. Smaller operation, and many of the finest players in NYC or the country, for that matter, as clients. If you want names, I'll give them.

Originally posted by Phil Smith
...Is it possible to get new bass feet and keep the top part of the bridge if your bridge is adjustable?Dirty quick-fix suggestion coming up - sensitive souls stop reading! :D:

I buildt the feet of my bridge higher by glueing on pieces of wood. Roughly cut squares of maple (whatever thickness required) with dowel-size hole in the middle, glued to bridge foot and clamped together with adjuster on for positioning. Filed even after glue had hardened.

Hey... 100! "New" gone... me member! :eek:

erik
Isn't it midnight where you are? When do you sleep?
Incidentally, there's a large Norwegian population about 1 hour from my home at - where else ?- Lake Telemark. The do allow a few Finns and Swedes to live there, too.

Originally posted by erik II
Dirty quick-fix suggestion coming up - sensitive souls stop reading! :D:

I buildt the feet of my bridge higher by glueing on pieces of wood. Roughly cut squares of maple (whatever thickness required) with dowel-size hole in the middle, glued to bridge foot and clamped together with adjuster on for positioning. Filed even after glue had hardened.

I like fixing stuff and I'm good at it, but there's a limit to how far I'll go. :D

Originally posted by Don Higdon
erik
Isn't it midnight where you are? When do you sleep?

I never sleep :cool:

Incidentally, there's a large Norwegian population about 1 hour from my home at - where else ?- Lake Telemark. The do allow a few Finns and Swedes to live there, too. Well, they are probably not allowed indoors...:D just kidding of course.
Guess you are referring to Lake Telemark in NJ (there is one in Kansas too). I'll have to go there some time - hang out in Lake Telemark Tavern. Maybe I'll bump into my mother's cousin Ella.

Originally posted by Phil Smith
I like fixing stuff and I'm good at it, but there's a limit to how far I'll go. :D Hey, it doesn't look that bad really :). Just to clarify: The "shims" sit on the top of the bridge feet, under the adjuster wheel. Pretty discrete, and a passable temporary solution.

I did this on the sad-excuse-for-a-bridge that was on my bass when I bought it. It was originally a training project for adjuster mounting - the bridge appeared to be beyond restoration. But lo and behold! - after some sawing, planing, filing and sanding, new adjusters - it didn't look bad at all. So the new raw bridge I bought still sits on the bookshelf.

Maybe you could ask a luthier or a shop if they have any wrecked bridges with feet intact lying around? Only problem I can think of is getting the holes in bridge and feet properly aligned.

Originally posted by brianrost
$850!!!

Boy am I glad I'm not in NYC.

I've had two fingerboards replaced up here in Boston, one was $400 some years ago (7?) the other was $500 two years ago. Both included other neck work (the $500 job included a reset, the bass had been in a car crash) as well.

Yeah, I'm with you. I had a fingerboard replaced with the top-grade ebony by Robertson's in Albuquerque and it was around $950 including fixing several cracks, new bridge, new strings, new soundpost, and new endpin.

I'm very curious about the Moses Graphite fingerboards. They are supposed to sound every bit as good as ebony as well as being more durable and cheaper. I probably need to put a new fingerboard on my Juzek in the next few years; I think planing again might make it on the thin side.

Monte

Originally posted by Monte


Yeah, I'm with you. I had a fingerboard replaced with the top-grade ebony by Robertson's in Albuquerque and it was around $950 including fixing several cracks, new bridge, new strings, new soundpost, and new endpin.

I'm very curious about the Moses Graphite fingerboards. They are supposed to sound every bit as good as ebony as well as being more durable and cheaper. I probably need to put a new fingerboard on my Juzek in the next few years; I think planing again might make it on the thin side.

Monte

I am thinking about one for my Juzek as well; it has some craters. A fellow who is building an EUB had contacted me over the last few months and we chatted about a fingerboard the last few days. I inquired with Steve Mosher of Moses, and in response to some queries about the fingerboard, adhesive use, shaping, and the nut choice, replied:


"Regarding our fingerboards:
Hyde glue is not suggested. Alyphatic Resin (Tight Bond) or or course 2 part epoxies are good.

For any touch-up shaping, most builders' choose to use sand paper, from 220 to 600/800 wet/dry. Traditional scraper's actually work fine with proper technique, but builder's are generally put-off with the idea of using them.

We have provided a surface area matrix material above the structural fiber. Therefore, there is never any tooling in the 'abrasive' fibrous carbon zone. This surface material is very abrasion resistant to string wear. It will thus be a very long time before any re-surfacing is required. To date, we have not heard of anyone needing to re-surface one of our boards.

We suggest using the traditional Ebony nut. For acoustic upright application, there really is no advantage to using graphite composite."

The boards are inexpensive in relation to most ebony boards. Contact me off list for a price if interested.

I think I may succumb to ordering one of his EUBs. For demo use, of course (don't tell my wife).

Bob,
I don't like the part about using epoxy, which I don't think should be used anywhere on a bass. Anyone else?

I'd probably use TightBond.

Originally posted by Don Higdon
Bob,
I don't like the part about using epoxy, which I don't think should be used anywhere on a bass. Anyone else?
I agree. You should have seen my Luthier freak when I went to get my Ebony fingerboard relaced, and he found out the previous one had been attached with Epoxy! He charged me extra for the time it took him to scrape all that crap off. I would say use Epoxy only if you never intend to replace your fingerboard. I can't really say what would be better for a Carbon Graphite board, though.

Hi sorry if Im hijacking this thread, I'm from London in the Uk and was wondering if anyone could tell me how much a replacement fingerboard and fitting will cost here in London.

Loving the site by the way, very informative :)

I just paid $1400 for a new Fingerboard, Nut, bridge adjustment, and to repair a crack in the heel of the neck. I'm in Chicago.
From what the luthier (Mark Sonksen) told me, $1000 of that was going to the Fingerboard and set up.
Mark did a good job, and I won't complain about the price since he lent me a very nice bass to cover some gigs and a recording session while mine was in his shop.
But Damn! This is an expensive axe to maintain.
Too bad electric uprights just don't cut it...
-Greg

Yeah my fingerboard cost just over $1000.00 in NYC. I need to learn luthier skills. :D