superbassman2000
03-05-2007, 06:45 PM
Hello all!
I am selling my Crown XLS402!
here is the info from the website:
8 ohms stereo-300W
4 ohms stereo-450W
8 ohms bridged-900W
The following applies to units in Stereo mode with 8-ohm loads unless otherwise specified.
Performance
Sensitivity (volts RMS) for full rated power at 4 ohms: 1.25 V.
Frequency Response (at 1 watt) 22 Hz to 20 kHz: +0 dB, –0.8 dB.
Signal-to-Noise Ratio (20 Hz to 20 kHz)
A-weighted, below rated power:
>98 dB.
No weighting, below rated power:
>93 dB.
Total Harmonic Distortion (THD): <0.5%.
Intermodulation Distortion (IMD):
(60 Hz and 7 kHz at 4:1) from full rated output to –40 dB: < 0.3%.
Damping Factor (8 ohm) 10 Hz to 400 Hz: >200.
Crosstalk (below rated power)
at 1 kHz: –76 dB. at 20 kHz: –58 dB.
Input Impedance (nominal): 20 kilohms balanced, 10 kilohms unbalanced.
Load Impedance: Rated for 2 to 8 ohms per channel in Stereo, 4 to 8 ohms in Bridge Mono.
AC Line Voltage and Frequency Configurations Available (±10%): 120 VAC 60 Hz, 100 VAC 50/60 Hz, 220 VAC 50 Hz, and 230-240 VAC
Controls
Level: Two front-panel rotary level controls, one for each channel.
Power: Front-panel switch; on when in the IN position.
Circuit Breaker: Back-panel breaker provides overload protection.
Mode Switch: Back-panel switch selects Dual or Bridge-Mono mode.
Signal Presence Indicators: Two green LEDs, one for each channel, illuminate when the channel’s input signal exceeds –40 dBu.
Clip Indicators: Two red LEDs, one for each channel, illuminate when the channel’s output is being overdriven.
Power Indicator: Blue LED indicates amplifier has been turned on and AC power is available.
Fault Indicator: Two red LEDs illuminate when amplifier is in protect mode. Also illuminates briefly during normal power-up when amplifier is first switched on.
Input Connectors: One per channel; back-panel three-pin female XLR input connectors.
Output Connectors: Two 4-Pole Speakon® Output Connectors accept 2-pole or 4-pole Speakon connectors. The top Speakon connector is wired for both channels so it can be used for bridge-mono wiring or for stereo wiring of two speakers to a single Speakon connector.
One pair of back-panel binding posts per channel; accepts banana plugs or bare wire.
Protection
XLS Series amplifiers provide extensive protection and diagnostic capabilities, including output current limiting, DC protection, circuit breaker, and thermal protection.
Construction
Ventilation: Flow-through ventilation from front to back.
Cooling: Internal heat sinks with forced-air cooling for rapid, uniform heat dissipation.
Air Volume Requirements (per minute per unit): 80.15 ft³ (2.27 m³).
Dimensions: EIA Standard 19-inch (48.3-cm) rack mount width (EIA RS-310-B), 3.5-inch (8.9-cm) height and 15.2-inch (38.6-cm) depth.
Weight
XLS-402: 25.7 lb (11.7 kg)
http://www.musicplace.ch/shop/images/products_big/003915.jpg
these are not real pics (gasp!) they are but mere graphic representations of the real deal--for pics of the one i am selling, pm me--but i will warn you, the images I will send you are not far from the graphics, because it is in great condition :)
I am looking for $200 plus shipping
thanks for looking!
I am selling my Crown XLS402!
here is the info from the website:
8 ohms stereo-300W
4 ohms stereo-450W
8 ohms bridged-900W
The following applies to units in Stereo mode with 8-ohm loads unless otherwise specified.
Performance
Sensitivity (volts RMS) for full rated power at 4 ohms: 1.25 V.
Frequency Response (at 1 watt) 22 Hz to 20 kHz: +0 dB, –0.8 dB.
Signal-to-Noise Ratio (20 Hz to 20 kHz)
A-weighted, below rated power:
>98 dB.
No weighting, below rated power:
>93 dB.
Total Harmonic Distortion (THD): <0.5%.
Intermodulation Distortion (IMD):
(60 Hz and 7 kHz at 4:1) from full rated output to –40 dB: < 0.3%.
Damping Factor (8 ohm) 10 Hz to 400 Hz: >200.
Crosstalk (below rated power)
at 1 kHz: –76 dB. at 20 kHz: –58 dB.
Input Impedance (nominal): 20 kilohms balanced, 10 kilohms unbalanced.
Load Impedance: Rated for 2 to 8 ohms per channel in Stereo, 4 to 8 ohms in Bridge Mono.
AC Line Voltage and Frequency Configurations Available (±10%): 120 VAC 60 Hz, 100 VAC 50/60 Hz, 220 VAC 50 Hz, and 230-240 VAC
Controls
Level: Two front-panel rotary level controls, one for each channel.
Power: Front-panel switch; on when in the IN position.
Circuit Breaker: Back-panel breaker provides overload protection.
Mode Switch: Back-panel switch selects Dual or Bridge-Mono mode.
Signal Presence Indicators: Two green LEDs, one for each channel, illuminate when the channel’s input signal exceeds –40 dBu.
Clip Indicators: Two red LEDs, one for each channel, illuminate when the channel’s output is being overdriven.
Power Indicator: Blue LED indicates amplifier has been turned on and AC power is available.
Fault Indicator: Two red LEDs illuminate when amplifier is in protect mode. Also illuminates briefly during normal power-up when amplifier is first switched on.
Input Connectors: One per channel; back-panel three-pin female XLR input connectors.
Output Connectors: Two 4-Pole Speakon® Output Connectors accept 2-pole or 4-pole Speakon connectors. The top Speakon connector is wired for both channels so it can be used for bridge-mono wiring or for stereo wiring of two speakers to a single Speakon connector.
One pair of back-panel binding posts per channel; accepts banana plugs or bare wire.
Protection
XLS Series amplifiers provide extensive protection and diagnostic capabilities, including output current limiting, DC protection, circuit breaker, and thermal protection.
Construction
Ventilation: Flow-through ventilation from front to back.
Cooling: Internal heat sinks with forced-air cooling for rapid, uniform heat dissipation.
Air Volume Requirements (per minute per unit): 80.15 ft³ (2.27 m³).
Dimensions: EIA Standard 19-inch (48.3-cm) rack mount width (EIA RS-310-B), 3.5-inch (8.9-cm) height and 15.2-inch (38.6-cm) depth.
Weight
XLS-402: 25.7 lb (11.7 kg)
http://www.musicplace.ch/shop/images/products_big/003915.jpg
these are not real pics (gasp!) they are but mere graphic representations of the real deal--for pics of the one i am selling, pm me--but i will warn you, the images I will send you are not far from the graphics, because it is in great condition :)
I am looking for $200 plus shipping
thanks for looking!