Note - neck is sold, body still available!
Another project I've decided to abort, but I hope someone will pick up where I've left off. This thread is for the body. Neck already to another TBer.
This body is that of an '82 Ibanez Blazer (made in Japan.) I believe it is mahogany with an ash top. It was originally a translucent purple, but, after many hours with dangerous cancer-causing chemicals in my garage (with the garage door wide open, a respirator breathing mask, goggles, and rubber gloves, of course) I managed to strip off the heavy clear poly finish and purple paint. It was not fun, but I did it just to say I could. You can still see some light purple stains here and there, and there is a purple square of finish underneath where the bridge goes, as well as purple finish in the neck pocket and control cavity. Obviously these areas will be covered once all the parts and hardware are in place. Neck pocket is a hair narrower than a Fender neck pocket - it's made to fit a neck that is about 2 and 7/16" wide.
I was planning on going the whole way with refinishing, but winter came, I got sidetracked, and lost interest. Then I tried again and got almost done. I had it all finished and half-way clear coated, when I tried to touch up a lumpy blemish with acetone. Needless to say, the acetone ate through the finish, and instead of just leaving it, I just took all the finish off. So now it's back to bare wood.
I will include all the original parts with the body. I recently polished the bridge meticulously with Brasso. While still pitted in places, it looks much better now than in the pictures. Also included are the original strap buttons, original white pickguard with original volume/tone pots (I also cleaned the pickguard with Goo-gone and that crud in the photos came right off - it looks nice now). I will throw in the original Precision-style pickups. I have the pickups pictured with the original black covers they came in, but I'll throw in the cream covers shown as well (cream covers are not original and are a little too big for the pickguard, but you can have them if you wish.)
Note: the neck plate and tuners were already sold, with the neck.
Everything for $100 shipped - lower 48 preferred. Money order, Paypal fine.
Some pics below. All pics here.
Another project I've decided to abort, but I hope someone will pick up where I've left off. This thread is for the body. Neck already to another TBer.
This body is that of an '82 Ibanez Blazer (made in Japan.) I believe it is mahogany with an ash top. It was originally a translucent purple, but, after many hours with dangerous cancer-causing chemicals in my garage (with the garage door wide open, a respirator breathing mask, goggles, and rubber gloves, of course) I managed to strip off the heavy clear poly finish and purple paint. It was not fun, but I did it just to say I could. You can still see some light purple stains here and there, and there is a purple square of finish underneath where the bridge goes, as well as purple finish in the neck pocket and control cavity. Obviously these areas will be covered once all the parts and hardware are in place. Neck pocket is a hair narrower than a Fender neck pocket - it's made to fit a neck that is about 2 and 7/16" wide.
I was planning on going the whole way with refinishing, but winter came, I got sidetracked, and lost interest. Then I tried again and got almost done. I had it all finished and half-way clear coated, when I tried to touch up a lumpy blemish with acetone. Needless to say, the acetone ate through the finish, and instead of just leaving it, I just took all the finish off. So now it's back to bare wood.
I will include all the original parts with the body. I recently polished the bridge meticulously with Brasso. While still pitted in places, it looks much better now than in the pictures. Also included are the original strap buttons, original white pickguard with original volume/tone pots (I also cleaned the pickguard with Goo-gone and that crud in the photos came right off - it looks nice now). I will throw in the original Precision-style pickups. I have the pickups pictured with the original black covers they came in, but I'll throw in the cream covers shown as well (cream covers are not original and are a little too big for the pickguard, but you can have them if you wish.)
Note: the neck plate and tuners were already sold, with the neck.
Everything for $100 shipped - lower 48 preferred. Money order, Paypal fine.
Some pics below. All pics here.
