/ Register

Recent Content by martininpv

  1. martininpv
    Post

    What do I need?

    Yes - I'm musicman on the Carvin boards.
    Post by: martininpv, Feb 27, 2002 in forum: Amps and Cabs [BG]
  2. martininpv
    Post

    Goliath III portability problem...Speakerhole?

    Better check the weight on the speakerhole cab. It may be just as heavy as your 4x10. You have to go through like you're going to order it...
    Post by: martininpv, Feb 27, 2002 in forum: Amps and Cabs [BG]
  3. martininpv
    Post

    Question for the gigging musicians

    I have a non-balanced line out on my amp. I run that to a DI and then to the board. My sound is probably half my rig/half PA. PA has EV 18"...
    Post by: martininpv, Feb 27, 2002 in forum: Amps and Cabs [BG]
  4. martininpv
    Post

    Need Help With My New Amp

    Bridging is when you connect the speaker(s) to the bridge only output and engage the bridge switch. Connecting from a speaker output to speaker...
    Post by: martininpv, Feb 27, 2002 in forum: Amps and Cabs [BG]
  5. martininpv
    Post

    Need Help With My New Amp

    With those speakers, you can either run bi-amped or full-range. You cannot run bridged because the impedence will drop below 4 ohms. So leave...
    Post by: martininpv, Feb 27, 2002 in forum: Amps and Cabs [BG]
  6. martininpv
    Post

    speakerhole.com

    It looks heavy on paper...
    Post by: martininpv, Feb 25, 2002 in forum: Amps and Cabs [BG]
  7. martininpv
    Post

    Anybody know where I can buy a speakon to speakon cable.....

    Carvin sells a 5 ft. 12 ga. but their shipping cost is high when ordering 1 small item. I also, would not consider 10 ft. too long. But 5...
    Post by: martininpv, Feb 20, 2002 in forum: Amps and Cabs [BG]
  8. martininpv
    Post

    Picking up radio, why and how do I stop it?

    What is the cable going into the effects return plugged into? If you are trying to use the Bassman's power amp, you will have to connect directly...
    Post by: martininpv, Feb 18, 2002 in forum: Amps and Cabs [BG]
  9. martininpv
    Post

    Picking up radio, why and how do I stop it?

    First, make sure that you are using shielded instrument cable for the guitar connection, the head to combo connection, and any effects units. If...
    Post by: martininpv, Feb 18, 2002 in forum: Amps and Cabs [BG]
  10. martininpv
    Post

    Horn crackling at low frequencies

    Are you sure it goes away when you turn the attenuator down? I had a cab with a horn that was distorting. Turning the attenuator down did not...
    Post by: martininpv, Feb 13, 2002 in forum: Amps and Cabs [BG]
  11. martininpv
    Post

    Horn crackling at low frequencies

    It's probably OK. That's what the attenuator is for. Turn it down until the crackle goes away. You may want to play a CD or something through...
    Post by: martininpv, Feb 13, 2002 in forum: Amps and Cabs [BG]
  12. martininpv
    Post

    Amp Problem

    Is it isolated to 1 of the power amps? If you use the other single power amp, is it OK? If both of the power amps work OK individually, it seems...
    Post by: martininpv, Feb 13, 2002 in forum: Amps and Cabs [BG]
  13. martininpv
    Post

    Amp Problem

    I don't know if I can figure it out, but I know those who might will need more info. Does it hum when nothing is plugged into it? Is the...
    Post by: martininpv, Feb 12, 2002 in forum: Amps and Cabs [BG]
  14. martininpv
    Post

    Power Amp Question

    I pulled up the Crate site. They did not have the BT350 in there. However, the bass amps listed had a pre-amp out specifically designed to drive...
    Post by: martininpv, Jan 21, 2002 in forum: Amps and Cabs [BG]
  15. martininpv
    Post

    Peavey Mark IV

    You can download the manual at www.peavey.com. I have a MARK III that I use now. It differs slightly from the MARK IV but it is basically the...
    Post by: martininpv, Jan 18, 2002 in forum: Amps and Cabs [BG]