/ Register

Recent Content by shrugs

  1. shrugs
    Post

    Using WinISD for Traynor TS-215 mod

    Ah alright so I will cut the port holes to the outer diameter of the PVC rather than the inner, so I can snuggly squeeze it in there. Sounds a lot...
    Post by: shrugs, Jan 14, 2022 in forum: Amps and Cabs [BG]
  2. shrugs
    Post

    Using WinISD for Traynor TS-215 mod

    No, I'm not sure at all lol, that's why I'm here. I started with 55Hz and got the idea of 27Hz from a few words bgavin suggested, but I may have...
    Post by: shrugs, Jan 14, 2022 in forum: Amps and Cabs [BG]
  3. shrugs
    Post

    Using WinISD for Traynor TS-215 mod

    Is that only true of solid state amps due to the lack of output transformer?
    Post by: shrugs, Jan 7, 2022 in forum: Amps and Cabs [BG]
  4. shrugs
    Post

    Using WinISD for Traynor TS-215 mod

    Oh in my original post I have 6 ports! All 3.5" x 6" which got me to a safe port air velocity
    Post by: shrugs, Jan 7, 2022 in forum: Amps and Cabs [BG]
  5. shrugs
    Post

    Using WinISD for Traynor TS-215 mod

    I was under the impression that the most common load for a bass amp was 4 ohms, so I was headed that route. I have a Traynor Monoblock B (solid...
    Post by: shrugs, Jan 7, 2022 in forum: Amps and Cabs [BG]
  6. shrugs
    Post

    Using WinISD for Traynor TS-215 mod

    Oh, I was under the impression that given my current WinISD setup (as seen in the first post and the graphs in reply to agedhorse), that I 100%...
    Post by: shrugs, Jan 7, 2022 in forum: Amps and Cabs [BG]
  7. shrugs
    Post

    Using WinISD for Traynor TS-215 mod

    Are passive HPFs not effective in general or just not in this scenario for some reason? So my expectations are 300W or greater power handling,...
    Post by: shrugs, Jan 7, 2022 in forum: Amps and Cabs [BG]
  8. shrugs
    Post

    Using WinISD for Traynor TS-215 mod

    I'm taking a look now at the Eminence Designer PDF for medium vented cab. As people have suggested I'll certainly need a HPF at 40 Hz. Do most of...
    Post by: shrugs, Jan 7, 2022 in forum: Amps and Cabs [BG]
  9. shrugs
    Post

    Using WinISD for Traynor TS-215 mod

    As bgavin already pointed out "Whether or not you NEED A0 is subjective, especially in a live mix." 27.5Hz is the fundamental of the lowest note...
    Post by: shrugs, Jan 7, 2022 in forum: Amps and Cabs [BG]
  10. shrugs
    Post

    Using WinISD for Traynor TS-215 mod

    Good to know! Thank you, I was just going off of what I've read. Never done the analysis myself. The space is pretty small, I already do this...
    Post by: shrugs, Jan 7, 2022 in forum: Amps and Cabs [BG]
  11. shrugs
    Post

    Using WinISD for Traynor TS-215 mod

    I've considered building a fEARful before! Lots of work but I'm sure it pays off. Are there any production cabs that are similar?
    Post by: shrugs, Jan 7, 2022 in forum: Amps and Cabs [BG]
  12. shrugs
    Post

    Using WinISD for Traynor TS-215 mod

    Do you have any bass cabinet recommendations that are 300W minimum, 2x15" configuration, and tuned low enough to hear an A0? It doesn't seem like...
    Post by: shrugs, Jan 7, 2022 in forum: Amps and Cabs [BG]
  13. shrugs
    Post

    Using WinISD for Traynor TS-215 mod

    Hey bgavin, I chopped up your quote a bit just to keep the parts I want to address. I do not think I NEED A0 fundamental, which is why I...
    Post by: shrugs, Jan 7, 2022 in forum: Amps and Cabs [BG]
  14. shrugs
    Post

    Using WinISD for Traynor TS-215 mod

    Thanks for the info bgavin. The lowest note that will ever be put through this cab is A0 which has a fundamental frequency of 27.5Hz. Is this what...
    Post by: shrugs, Jan 7, 2022 in forum: Amps and Cabs [BG]
  15. shrugs
    Post

    Using WinISD for Traynor TS-215 mod

    Here are my graphs:[ATTACH] [ATTACH] [ATTACH] [ATTACH] NOTE: I re-measured my cab and it comes out to 6.21 ft^3. Probably wont make much...
    Post by: shrugs, Jan 7, 2022 in forum: Amps and Cabs [BG]