Separate names with a comma.
Last week, after one soldering too many, my poor and abused CTS volume pot in my P had the "input" lug (where you wire the pickup) which started...
How would I go about doing this, and would it be possible without having to re-solder and rewire the P pickup that is currently installed in my...
Hi TB, I've always found these forums to be a wealth of knowledge, so I'm hoping that to be the case now. I'm currently in Stage 4 lockdown here...
I'm looking to convert the control scheme on my Schecter Diamond-P Custom 4 -- It's a passive bass with a P-bass pickup and a humbucker which can...
So I bought an expression pedal to use with my Behringer US600 Ultra Shifter pedal because I wanted to avoid stepping on its infamous weak plastic...
Hi, My sterling's potentiometers aren't working, I tried with wd40 deoxidant but the bass and treble pot aren't Linear and if I try to...
This happens on my beloved Moollon bass, which I bought from a friend. The bass plays very well without any noise issues. However; only sometimes...
Hey folks I recently acquired a 1960 Pre-CBS Fender Precision refin. It plays like a dream but I find it gets a bit honky when I dial the tone...
So I more or less decided I am going to install a blend pot in my Ibanez Mikro bass, in which I installed a pair of P/J EMG Geezer Butler pickups...
My favorite bass is acting up. With the Tone set below full, It will jump by itself to full-on-bright. It can be any setting such as 25%. It will...
What do I need to know? I'm looking at converting a bass that comes with a two band pre to a passive. Easy to do for a novice at soldering or...
I have this active circuit that has the following known functions: [ATTACH] 1 pickup 3 way selector switch 2 volume 3 bass 4 treble Here are...
I want to wire my Squier CV Jazz bass for series/parallel operation. I found this pot online. Is this the right shaft length, diameter, taper,...
I'm trying to figure out if my tone pot is acting as it should or if it needs replaced. On the way from 1-5 there is a noticeable volume...
[ATTACH] why are there two sets of lugs on the pot portion of this? The push pull only operates the switch portion. I only need three lugs like a...
I have a '72 Traynor YBA 1 Bass Master. I don't know a lick about amps, let alone tube amps, and I'm curious if something is wrong with the amp....
I'm a bit bewildered by the EMG pickups and wiring. Is there a way to wire two EMG 35P4 pickups with three pot holes and a jack? I want to just...
Hi there, Just parting out a P bass and have this but don't need it. This is a really great and normally overlooked P pickup. These are stock in...
It really seems that my bad ground hum karma won't go away. I decided to gut my bass of its existing active/passive electronics (& Carvin pickups)...
I'd like to swap out the lipstick pickup and the pots on a Harley Benton Resobass. Perhaps the cone as well. I'm looking for recommendations. The...
Hi first post on site so go easy on me i need to replace volume pot on my Ibanez SR1200 anyone know the value (resistance) and is it Logarithmic...
So I run a Sire v7 active bass and I love it. I have had no problems with it up till now, it plays great and the tones I can get out of it are...
In need of some advice regarding a replacement volume pot on a late ’70s Mustang bass: Last night, the pot got stuck and this morning, in...
Stating up front that I'm completely electronics ignorant. The blend pot on my SR1825 has started going wonky. Signal cutting out when panning,...
I have a Peavey Millenium BXP 4 thats having a weird issue with the tone pot. When I open the tone all the way, it actually closes it at the...
So I'm adding a second volume control to my CIJ Fender Jaguar bass which comes standard with one volume and one tone. My noob question is that...
Hello, I've been looking into 'fixing' my lefty G&L SB-1 which comes with audio taper pots wired in reverse, effectively making both the volume...
I recently bought a used used toby and the active pot has been removed from the pick up circuit. The bass still produces sound. With out the...
Hello fellows, I'm looking for a schematic for bypassing the tone pot and to leave just the volume straight to the jack. I saw some old threads...
Hi, Does anyone know the specs of the main volume pot for an Ampeg PF 500. If you have an online link please share the link here. regards g
Years back I tried a set of Dimarzio pickups and utilized the stock 250K pots in the bass I put them in. They were so muddy they were unusable. I...
Salut all ! I did this on my geddy lee bass (Crazy Modded Geddy Lee Jazz bass ( SMB-4D + OBP-1 ) ) : I add a master volume pot (250k) after the...
Hey all, Tone pot on my PJ Squier goes in an out when I tap it, and, increasingly, does so on its own. I am taking this repair opportunity to...
Does anyone know if there is a aftermarket replacement for this? Our club foot singer knocked my bass over and broke the pot, it's volume and...
So I opened my 2006 Hwy1 Jazz Bass and I found out that the 250k tone pot has two caps, one standard .02uF on the 3rd lug to ground and a second...
I'll post the questions first, the background and info behind the questions can be found in my long winded post below. I have searched TB and...
I have a MIM Precision Bass and would like to install a switch that mutes the signal to the output jack without changing its look. I figured using...
The single tone pot on my jazz bass seems to work *some of the time*, but not all the time. I'm totally perplexed. I had a bad tone pot that just...
Here's the story. I bought an open box 'scratch and dent' Ibanez SRC6 (Ibanez bass VI) from musician's friend. This sucker looks mint. I tried...
Hello fellow bass players! Quick question: do any of you know the value of the tone pot found on a SBMM Ray34ca (2 bands preamp)? I just acquired...