Separate names with a comma.
Hey I try to look in google but I did'nt find where I can buy a master vol. Pot for a Fender rumble 500 v3 combo.. I broke it I don't know how but...
Hey folk, I would like to confirm and clarify some questions I have about Jazz bass wiring mods. Is it possible to do a Mod with the following ?...
Hey, guys. So I currently have this 2 knob bass that's volume/volume. Both of the pots are 250k... I want to replace them with 2 concentric knobs...
Hello, I recently obtained an empty Gibson G-3 pick guard with a single Jazz Bass pickup in the third position. I also obtained 2 stock Gibson...
So I more or less decided I am going to install a blend pot in my Ibanez Mikro bass, in which I installed a pair of P/J EMG Geezer Butler pickups...
In need of some advice regarding a replacement volume pot on a late ’70s Mustang bass: Last night, the pot got stuck and this morning, in...
I was thinking of moving my output jack from the pickguard to the side of the body and adding an extra pot/knob in the output jack hole on the...
Stating up front that I'm completely electronics ignorant. The blend pot on my SR1825 has started going wonky. Signal cutting out when panning,...
So my Fender Jazz (MIM Geddy Lee) had no shielding or ground wire to the output jack. I used MG solutions silver paint to do all the cavities and...
Hi, I have a guitar with passive pickups and Aguilar OBP-3 preamp. it's wired as 250K M/N blend -> 500K volume -> preamp I'm thinking of adding...
To modify bass guitars. i need some pots which require following options : 25k ohm Linier type solid shift Push-Pull option Center Click...
I’m fairly new at soldering but I’ve begrudgingly decided to do something with my soldering iron cuz I hadn’t used it in a while. I was...
So I ordered the OBP-3 preamp for my Ibanez SR506 to do a swap. I was excited! But after I ordered the preamp, I realized that it only came with...
Hey Yall, I'm swapping out the pups and electronics in my Squier J bass for the pups and electronics from a Deluxe series bass (among many other...
Salut all I have a bass equiped with an Aguilar OBP-1 preamp. I bought the "STK" version , which comes with stacked potentiometer. It works fine...
Hello all Does someone know the impedance of the volume potentiometer in a Modulus Flea Bass/Funk Unlimited ? Since the bass is equiped with a MM...
Hello guys! I'm purchasing a used Aguilar DB 680 preamp. The XLR Balanced Output pot is not correctly working (is turning continuosly, not with...
I have a bass that needs a new volume pot. The current one is scratchy and creates a huge amount of static when i adjust it. Being the volume...
Anyone know where I could find a potentiometer that is a lever instead of a knob? I'm sure something like that exists. [ATTACH] Something like...
Hi Guys, I bought a used SR405 for 150 with a broken (physically - you cant turn it left or right) mid control. I'm using it mostly for practice...
I was putting a knob on a tone pot, it was kind of tight, I was pushing hard and heard a pop. Now the shaft feels like it is on a spring and can...
Hello! The Contour pot of my old Fender Bassman 250 is broken, could somebody tell me how can I find out the exact model that I need to order for...
Greeting I have some Lollar Thunderbird pups with 500k audio taper pots for volume in one of my basses in a VVT config With a small turn of the...
This is a little device I built to audio test out pots without having to solder them in. I used a half a P-bass type pickup, a tuning fork to...
Hey all, I've been working on circuit-bending my tascam, and I'm wiring up a pot to control the current to the motor so I can change the speed,...
I'm repairing a bass for a friend and it needs a replacement pot. Typically, not an issue for me. I've replaced pots lots of times, but this one...
I have a passive early 90's Peavey Fury with a shot tone pot. I'll likely get a new 250k one soon, but I have a spare 10k audio taper pot. I know...
Hi Everybody, it's my first post here :) I have a 90's MIJ j-bass, and it's really great, but I feel that I need to upgrade it to get that extra...
I'm thinking of using a staked pot for 2 volumes (2 pickups). I'm guessing there's nothing wrong about that technically, am I right? (First mod...
Hi, 1) The tone potentiometers in the preamp of one of my bases are completely stuck and doesn't turn anymore. I have tried contact cleaner with...
Hello fellow talkbassers! I have a question that I know someone here can help me with. Here goes. I'm going to be installing new Seymour Duncan...
Basically, the treble knob broke off... there's nothing to grab on to. I'm wanting to trade it towards an ashdown 220 combo, so I'm hoping to...
I picked up a GBE-1200 bass amp. 2 of the pot shafts are sheared off...and it is missing those respective knobs. I have searched for the pots,...
hello there are a few questions I have, as I am rewiring a stratocaster (i know not a bass sorry) and a ibanez GSR-200 wnf bass 1. if a tone knob...
I have 3 alpha pots with unknown values. Can I use a multi meter to determine the value of these pots?
Had a scratchy pot. Many a forum thread recommended DeOxit. But I thought DeOxit was too expensive at $12.00. So instead... I moved the pot...
Hi, I have a bassmods preamp, one vol pot, one balance pot, one stacked for mids and one stacked for bass and treble. I need to change the volume...
Hi all, hope all is well. Just need some electrical advice. I have just bought and Ibanez premium bass with a mid frequency switch instead of a...
