Separate names with a comma.
Hey guys!!! I need some recommendations on how to repair these nasty gouges. I recently scored a 60's classic vibe jazz Bass for $100 and would...
EDIT: Measurements of the TRBX305 pickups attached, white bass Hi all, I have two Yamaha TRBX305 basses, white & red. Both have some issues I'm...
[ATTACH] I am brand new to bass. I had recently noticed the volume knob on the bass felt pretty loose but before I could get it checked out I one...
I just purchased a SWR workingmans 2x10T cab along with in SWR SM 500 head and an Ampeg SVT 1015 cab. I'm having troubles with the two 10 cab with...
I took delivery of a brand new Ibanez GSRM20 Mikro bass today, and was immediately disappointed to find that it had suffered a significant dent in...
I have fender bass with gloss urethane finish. There's a small crack that I noticed today, and was wondering if there's any kind of recommended...
OK, here's the situation. I'm a sax player who's just fallen in love with double bass. The only problem is I can't afford to buy a decent one....
I have a 1970's SVT that sat on a shelf for about 5 years. Previously serviced by Dennis Kager in Linden NJ. Since I don't have access to a car,...
I have a bass that needs a new volume pot. The current one is scratchy and creates a huge amount of static when i adjust it. Being the volume...
So I put on a new set of strings on my Fender Pbass (went from Rotosound 45-105 to Ernie Ball 50-105) because I'm going into the studio in a few...
So I recently picked up a used Hendrix signature crybaby for dirt cheap and the tension on the pedal is super low. It doesn't spring back at all....
Back in the 70's/80's/90's, when I was playing fulltime, Sunday was my strip down day to improve my basses for the upcoming week. ... So, other...
[ATTACH] I have no dog in this fight, but am throwing my hat into the ring to support, what I feel, is an amazingly talented electronics and amp...
The small input jack on the back of the amp has lost its retaining nut that holds the jack to the amp. It is the nut that retains the female jack...
shoot. My almost 20 year old Eden WT-600 head is starting to have issues. It seems it's having power issues... Yesterday it was losing power and...
Hey everyone! So I picked up a laminate bass on the very cheap yesterday. Everything points to it having it having great potential as a fun...
Hi there I have an 30-year old Carlsbro Hornet 45 Amp in need of repair. The cone looks in really good shape but the electronics are a bit dodgy...
Hi everybody, I'm repairing my AG500SC head, which had a burned cemented resistor. As I'm reassembling it, I'm ashamed to admit that I hadn't...
I tryed to film an effects demo today and once I started recording I got no sound coming from my bass. This happened before at a gig. I should...
gotta 410 gallien krueger glx cab from a pawn shop and it had a blown speaker. i want to replace the blown speaker but i cant find one online....
Can't remember when I bought this thing new, but has been a hoss until now... constant hissing when idle... then really bad fuzz during any kind...
I am repairing a Acoustic 140 bass amp head. It has 4 RCA 2N4348 TRANSISTORs install from the factory. Two of them are shorted to ground. I can...
Hey Guys was wondering if anyone had experience with getting a ribbon mic repaired. I bought a Troll Mic, I know it is possible to send it to get...
Looking for advice to repair a big chip in the paint of my geddy lee. I guess i could use superglue to seal. But where to find matching paint??...
I have Fender B X R Sixty Bass amp . It needs new input jacks . It works , with a replaced input Jack ! The problem is , sometimes the signal...
I have a 73 Jazz Bass. The bridge pickup died and I had it rewound by Curtis Novak. He did a great job. I had my tech install this repaired...
Hello Vancouver bass folks: Has anyone taken an amp to Mr. Ho lately? I hear he's still around, but I have hot and cold reports about his...
I picked up my Squier VM Jazz Bass today and I noticed that one of the clover head machine heads was bent. When I tried to straighten it, the...
Hey guys, I know this is a long shot but I figured I might as well try. I have a Polytune 2 (bought new) that decided to malfunction now that...
Lynn Armour Hannings gets mentioned not infrequently here due to her bow re-hairing and bow making courses. Probably less often for her bowmaking...
Hi all, One of the cones in my TE 2103x started farting recently. Couldn't see any damage on the face, but upon removing the driver, it's clear...
I was listening to NPR radio this morning and they were discussing "right to repair" legislation (something I'd never heard of before). Seems...
Are there any repair shops in the SE PA area that has a Stew Mac truss rod rescue kit? The end of my '77 T-Bird truss rod snapped off. My local...
I've been playing bass for about 6 years now, The first bass I bought was an Epiphone Gothic Thunderbird IV secondhand on the way to audition for...
I'd like to get some advice from the pros on how to repair and restore nitro lacquer finishes on a Kay or other American plywood bass, 1930s to...
Hi all - I am working on a project with a vintage eb-3 copy i got from CL for $50. The finish, being a older guitar, is starting to chip in...
I have an 8x10 ampeg cab and blew one of my 10 inch speakers. What's the best way to go about replacing the speaker? DIY remedy? What is the cost...
Does anybody know whether these jack sockets from a Fender Amp can be opened for cleaning? [ATTACH]
There is a Fender BXR 300C at my school that has been non functional for about 2 years. It may get taken to a shop at some point, but I'm...
Hello, I'm looking for recomendations for a DMM for audio repair. Think 120v and less stuff, synth and drum machine repair, trouble shooting, mic...
