/ Register

Aguilar GS210 Tweeter Wiring terminal HELP!

Discussion in 'Amps and Cabs [BG]' started by Rea, Dec 14, 2014.

  1. Dec 14, 2014 #1
    Rea

    Rea

    Dec 10, 2014
    Brooklyn
    Hi-

    Bought a GS210 with a bad Tweeter. Opened it in order to check what's up but puleed its Cabels from the terminal on the back wall. Now i want to simply reconnect it but not sure where the wires go as there are 4 possibilities.

    Can anyone tell me where the + and - go according to the pic? photo-1.JPG
     
  2. Dec 14, 2014 #2
    OldogNewTrick

    OldogNewTrick

    Dec 28, 2004
    Germany, EU
    here you go....
    GS210 connections.jpg
     
  3. Dec 14, 2014 #3
    Rea

    Rea

    Dec 10, 2014
    Brooklyn
    It looks quite different, or maybe im just not getting it...

    Looking at my Pic, can you tell me, out of the 4 unused "tongues" where + and - goes?

    Thanks again!
     
  4. Dec 15, 2014 #4
    Rea

    Rea

    Dec 10, 2014
    Brooklyn
    Still need help w this. Aguilar suppprt is mot available somehow. Can anyone chime in?
     
  5. Dec 15, 2014 #5
    B-string

    B-string

    Nov 21, 2008
    Lake Havasu City, Az USA
    Can you get a better lit pic of your crossover board? Could probably figure it out. Did the wires detach from the tweeter horn or the crossover (plate mounted to the back)?
     
  6. Dec 15, 2014 #6
    Rea

    Rea

    Dec 10, 2014
    Brooklyn
    Getting you a pic in a few minutes. The cable detached from those "tongues" in the back. Its a no brainer reconnection, i just dont want to connect it wrong...;(
     
    B-string likes this.
  7. Dec 15, 2014 #7
    Rea

    Rea

    Dec 10, 2014
    Brooklyn
    image.jpg
     
  8. Dec 15, 2014 #8
    B-string

    B-string

    Nov 21, 2008
    Lake Havasu City, Az USA
    I can't make out an open lug for the (-) negative to the tweeter, but the red positive was easier:
    Ag tweeter.jpg
     
  9. Dec 15, 2014 #9
    Rea

    Rea

    Dec 10, 2014
    Brooklyn
    The black arrow is pointing to a terminal that is already taken i believe. What else can it be?
     
  10. Dec 15, 2014 #10
    B-string

    B-string

    Nov 21, 2008
    Lake Havasu City, Az USA
    Follow that black wire to the input jacks (from that board) and see if there is an open lug there at the same place the black wire attaches.
     
  11. Dec 15, 2014 #11
    Rea

    Rea

    Dec 10, 2014
    Brooklyn
    So basically it should short with the red and black on the left?
     
  12. Dec 15, 2014 #12
    B-string

    B-string

    Nov 21, 2008
    Lake Havasu City, Az USA
    NO. The center wire from the control on the top with three wires needs to go to the + or red dot on the tweeter, there should be an open lug on the board where that attaches to. From there you need a - (negative) to go to the tweeter (usually black, or dark color wires). If the black is a short wire from the tweeter it could have been attached to the black or negative on one of the woofers. That is not a short if I am misunderstanding your choice of terms, it is completing a circuit.
     
    Last edited: Dec 15, 2014
  13. Dec 15, 2014 #13
    Rea

    Rea

    Dec 10, 2014
    Brooklyn
    OK got it, The Postive was the one you put the red arrow to and the negative is the one right under the brown one in the pic. Thanks!
     
  14. Dec 15, 2014 #14
    B-string

    B-string

    Nov 21, 2008
    Lake Havasu City, Az USA
    Yes, the right brown wire was covering the red (positive connection) in the pic. The negative should be at the left brown wire and the blacks.