Separate names with a comma.
Discussion in 'Amps and Cabs [BG]' started by Ignus, Jul 27, 2001.
Post your Eq settings here....
That's an easy one. On a good amp, flat. Flat. And FLAT.
Unless the room is seriously bad (sure, some are), I seldom touch EQ on any of my amps. Currently, I'm using:
'00 Eden WT400
'98 Eden WT800
'00 SWR Bass 750
'01 Mesa Boogie 400+
I also occasionally run a Bass POD Pro as a preamp through a QSC850 power amp.
I always try to EQ the instrument rather than the amp. This is especially effective on active basses.
i was going to post something like this, but i didn't know where to put it.
on my amp (3 band, with a range from -5 - +5) i have treble at +3-4, mids at -2-3, and bass at +4-5. On my one tone knob i have it almost all the way.
SWR Workingman's 4004
range is from -15 to +15
80hz ( bass ) = +7
160hz ( low mid ) = +5
400hz ( mid ) = +4
800hz ( high mid ) = -2
3khz ( treble ) = +4
I do most of my EQ'ing with the on-board EQ of my Ibanez EDC705.
does that come out a little muddy? Just curious.
Low, Mids, and High knobs all at 50%.
EQ at 0 (50%) on ends gradually getting up to about 4 in the middle making a slight frown-face.
On my AMP BH-420...flat across the board.
On my Ampeg B-100R 5-3-3-5, switches off.
Several settings depending on the situation:
usually 5 - 4 - 5,
sometimes 4 - 4- 6 if I'm playing harmonics a la Jaco.
4 - 5 - 4 on the fretless.
Totally flat on my swr sm900 and i use my mike pope pre amp to shape my tone.for slap bass tone i usually scoop some mids out and boost the bass and treble just a bit.for finger style i boost the mids a bit and tune the treble and bass to the particualr room.
p e a c e
not realy...depends a lot on how the EQ on your bass / effect-pedals are set i guess... my Eden CX410 cabs give nice sound with it
High preamp fileter on
mids-cut by half
highs-all the way up
Hey, somebody's gotta do it.
volume - 11
bass - 11
low mid - 11
high mid - 11
treble - 11
Dangit Nerve!!! Beat me to it!!
Kern preamp - all flat
on my amp, flat. on my sansamp, bass and treble both rolled off a little, drive at 2 o clock, presence at 1 o clock.
Graphic EQ - Flat
Well here they are, a little basic but hey.
Ampeg SVT-3 PRO;
Ultra Low on
Tube Gain= 8
Drive= 1 1/2
Ultra Low on
Both chanels combined
Treble= 6 1/2
more volume from clean
Gain= 9 set to distortion 3 on overdrive
less volume from dirty
Hmm, I have about 15 patches on my ADA so far, but here is my semi scooped patch. Actually, it is not really scooped, but it is alright.
Low Mid 6 @ 166 Hz
Mid -3 @ 545 Hz
Hi Mid 6 @ 610 Hz
parametric boost at 1 o'clock(12 is flat) at about 1.5 khz
it depends on the bass i'm playing. more than the amp.
with the 82 japanese squier jazz the EQ is flat
with the 80 rickenbacker 4001 i boost the basses 7 on 10 and cut the highs 2 or 3 on 10
with the 97 gibson hunderbird i have 2 options: if i want a jazz style tone i cut the basses, 3 on 10. if i want to rock like an hammer i boost the basses, the mids at 7 on 10.