A RARE beast out in the wild and for sale!!
The ARKHAM BEAST OF BOTH WORLDS!
I'm only selling as I'm getting a vintage Wurlitzer for my home studio and need to gather funds. I have a 1965 Ampeg B15 as well as a 1967 Ampeg SB12. The Arkham BOBW is a wonderful modern take on these classics sounds. There's something special about the preamp design matched with this amount of power! The word "heft" comes to mind. TONAL AUTHORITY!
This particular unit was recently serviced by Micah himself (the man behind Arkham Sound) and given a clean bill of health.
While I will certainly miss the Beast, I'm sure the next owner will treat it well and enjoy the experience!
I'm including a custom Studio Slips carry bag, made for this unit. Minus a couple scratches and the slight imprint of a sticker on top, this thing is in great shape.
$1350 shipped and insured, ConUs.
ONLY trade interest would be an Aguilar DB112.
You can find this listing on Reverb for those that need a payment plan
Class D power section delivers 1200W into 4 ohms, 600W into 8 ohms
12AX7 preamp tube selected for low noise and good tone, and powered with a dedicated 300V supply (not a starved plate design)
-6dB input pad
Gain, Treble, Bass controls - uses a James Tonestack to provide a wide adjustment range with minimal interaction
Range control sweeps the tonestack "midpoint" anywhere between 150Hz and 1KHz
Hi switch adds a "bright cap" to the circuit to open up high frequencies a bit
Mid switch gives a +3dB boost at 150Hz
Lo switch gives a +6dB boost at 80Hz
HPF switch - Passive filter(-6dB/octave) set at 100Hz
Integrated Subsonic Filter - active, 24dB/Octave HPF set at 30Hz. Tames low frequency cone excursion, allowing for more power and clarity in the audio band.
Mute Switch
Amplifier and DI Out Master Volumes
LED Clipping Indicator
Preamp Out and Power Amp In jacks double as a series, line level Effects Loop
Parallel Speakon speaker jacks
Balanced DI output, featuring a hefty Cinemag transformer and ground lift switch for good measure
Turret board construction for high voltage circuits, Mil-spec Teflon wire, etc
Top quality components throughout
Heavy gauge aluminum chassis. 13" x 13" x 3.5" overall dimensions. Weighs ~ 9.2 lb.
The ARKHAM BEAST OF BOTH WORLDS!
I'm only selling as I'm getting a vintage Wurlitzer for my home studio and need to gather funds. I have a 1965 Ampeg B15 as well as a 1967 Ampeg SB12. The Arkham BOBW is a wonderful modern take on these classics sounds. There's something special about the preamp design matched with this amount of power! The word "heft" comes to mind. TONAL AUTHORITY!
This particular unit was recently serviced by Micah himself (the man behind Arkham Sound) and given a clean bill of health.
While I will certainly miss the Beast, I'm sure the next owner will treat it well and enjoy the experience!
I'm including a custom Studio Slips carry bag, made for this unit. Minus a couple scratches and the slight imprint of a sticker on top, this thing is in great shape.
$1350 shipped and insured, ConUs.
ONLY trade interest would be an Aguilar DB112.
You can find this listing on Reverb for those that need a payment plan
Class D power section delivers 1200W into 4 ohms, 600W into 8 ohms
12AX7 preamp tube selected for low noise and good tone, and powered with a dedicated 300V supply (not a starved plate design)
-6dB input pad
Gain, Treble, Bass controls - uses a James Tonestack to provide a wide adjustment range with minimal interaction
Range control sweeps the tonestack "midpoint" anywhere between 150Hz and 1KHz
Hi switch adds a "bright cap" to the circuit to open up high frequencies a bit
Mid switch gives a +3dB boost at 150Hz
Lo switch gives a +6dB boost at 80Hz
HPF switch - Passive filter(-6dB/octave) set at 100Hz
Integrated Subsonic Filter - active, 24dB/Octave HPF set at 30Hz. Tames low frequency cone excursion, allowing for more power and clarity in the audio band.
Mute Switch
Amplifier and DI Out Master Volumes
LED Clipping Indicator
Preamp Out and Power Amp In jacks double as a series, line level Effects Loop
Parallel Speakon speaker jacks
Balanced DI output, featuring a hefty Cinemag transformer and ground lift switch for good measure
Turret board construction for high voltage circuits, Mil-spec Teflon wire, etc
Top quality components throughout
Heavy gauge aluminum chassis. 13" x 13" x 3.5" overall dimensions. Weighs ~ 9.2 lb.
