Recent content by evic777

  1. E

    wiring diagrams to change blend pot to 2 volumes

    I went back and re-did all my ground. Is there any easy way to check for cold solders Sent from my ALCATEL_one_touch_995S using TalkBass mobile app
  2. E

    wiring diagrams to change blend pot to 2 volumes

    Hopefully this will post
  3. E

    wiring diagrams to change blend pot to 2 volumes

    Will do... I will post it in an hour or so Sent from my ALCATEL_one_touch_995S using TalkBass mobile app
  4. E

    wiring diagrams to change blend pot to 2 volumes

    Dmusic148 Finally got around to tackling this mod. I have everything wired as diagrammed. The yellow input to the NTMB918F preamp to the left lug of the bridge. The green out put from the preamp to the + tip of the output jack It works but the gain is significantly lower that before and when...
  5. E

    wiring diagrams to change blend pot to 2 volumes

    oh... Obviously post 4 confused me a bit (easily done LOL) If I understand... If I am NOT installing a Master Volume I will not bridge the two volume together like the diagram shown above. Each volume pot will independently connect to the output tip along with the yellow preamp input. Correct?
  6. E

    wiring diagrams to change blend pot to 2 volumes

    To clarify... I have 2 bart humbuckers (99% sure they are passive) and NTMB918 pre I have two 25K pots... would you use them or replace with 250K ??? Do I connect the YELLOW preamp wire to each volume pot where my each of my pu are connected??? Will I be able to solo each pu? Once again... THANKS
  7. E

    wiring diagrams to change blend pot to 2 volumes

    Line6man... After reading many posts until my eyes began to blur I think I am going to wait on adding a master volume and try the 2 individual pu volumes first The current volume pot in the bass is 25K Can I just add another 25K What recommendations for you have ... I value your opinion Thanks!
  8. E

    wiring diagrams to change blend pot to 2 volumes

    Exactly how do I do that? I have the preamp that you have in your link. And where do I attached the YELLOW wire from the preamp that was connected to the blend pot? Thanks!
  9. E

    wiring diagrams to change blend pot to 2 volumes

    Exactly what I needed. Once again... Thank you and also... Merry Christams
  10. E

    wiring diagrams to change blend pot to 2 volumes

    Thanks Line6man! Anyway you could send a brief diagram? Curious where the preamp wire fits in to this? Thanks!
  11. E

    wiring diagrams to change blend pot to 2 volumes

    Hello Help! LOL I have an NTMB918 Preamp. I want to remove blend pot and wire for 2 individual volumes and a master volume. Can anyone provide a basic diagram? I have one hot (yellow) wire that goes to my blend pot. I'm assuming I need to connect that to each volume pot??? I just do not...
  12. E

    Warrior Sam Ash GenerationX 5 string

    Does anyone have any experience or information on these basses? I've played a Warrior and loved it but I'm curious how the GenerationX stacks up. A guy has offered this bass in a trade for my Modulus Q6 Thanks for your input!
  13. E

    Dean Club!!!

    After a complete set up it plays amazingly well (VERY HOT 18 VOLT PREAMP) Thinking I might convert to a fretless or trade it towards one??? ANYONE OUT THERE WITH A FRETLESS THEY WANT TO TRADE?
  14. E

    Fretless Six String?

    Curious... What did you think about the Douglas?
  15. E

    Dean Club!!!

    Just traded for a Dean Quilted 6... It was a filthy pig that needed a lot of work. An intense cleaning, frets leveled, complete neck adjustment and a set of DR FatBeams and all is GOOD! I got it CHEAP and after about 6 hours on the bench I am very impressed. I did not expect it to play as...
See more
Top Bottom
Back