MANUAL
CREST Pro-LITE 3.0: https://bit.ly/crestprolite3
Superb condition, very clean, works perfectly, zero issues
Price includes FedEx / UPS GROUND shipping in the CONUS ONLY
FOR SALE ONLY, NO TRADES
PayPal or Venmo payment accepted
PM with questions
SPECS below.
Thanks!
_____________________________________________________________________
Crest® Pro-LITE® 3.0 Specification Sheet
Rated Power Bridge 4 ohms 3640 watts 20ms repetitive burst / 3000 watts 1% THD @ 1kHz.
Rated Power Bridge 8 ohms 2000 watts 20ms repetitive burst / 1550 watts 0.15% THD @ 1kHz.
Rated Watts 2ch x 2 ohms 1820 watts 20ms repetitive burst / 1500 watts 1% THD both channels driven
@ 1kHz.
Rated Watts 2ch x 4 ohms 1000 watts 20ms repetitive burst / 900 watts 1% THD / 830 watts 0.15% THD,
both channels driven @ 1kHz.
Rated Watts 2ch x 8 ohms 540 watts 20ms repetitive burst / 500 watts 1% THD / 450 watts 0.15% THD,
both channels driven @ 1kHz.
Minimum Load Impedance 2 ohms
Maximum RMS Voltage Swing 71 volts
Frequency Response 20Hz - 28kHz; +0dB, -3.0dB at 1 watt.
20Hz - 20kHz 2ch x 2 ohms <0.5% @ 1350 watts at 20Hz increasing to 1380 watts at 20kHz, both
channels driven.
20Hz - 20kHz 2ch x 4 ohms <0.15% @ 800 watts at 20Hz increasing to 850 watts at 20kHz, both
channels driven.
20Hz - 20kHz 2ch x 8 ohms <0.15% @ 450 watts 20Hz increasing to 500 watts at 20kHz, both
channels driven.
Input CMRR > - 76dB @ 1 kHz
Voltage Gain x 75 (+37dB)
Crossover 100 Hz switchable 2nd order high pass and 3rd low pass per channel.
Crosstalk > -70dB @ 1kHz @ 250 watts power @ 8 ohms.
Hum and Noise > -100 dB, “A” weighted referenced to rated power @ 4 ohms.
Slew Rate > 12V/µs
Damping Factor (8 ohms) > 255:1 @ 20Hz - 1kHz @ 8 ohms.
Input Sensitivity 0.740 volts +/- 3% for 1kHz 4 ohm rated power, 0.710 volts +/- 3% for 1kHz
2 ohm rated power
Input Impedance 15k ohms, balanced and 7.5k ohms unbalanced.
Current Draw @ 1/8 960 (540) @ 2 ohms, 620 (320) @ 4 ohms, 400 (190) @ 8 ohms
power in VA (watts)
Current Draw @ 1/3 2070 (1310) @ 2 ohms, 1220 (700) @ 4 ohms, 740 (400) @ 8 ohms
power in VA (watts)
Idle Consumption 140VA, 60 watts.
Cooling Temperature dependent variable speed 80 mm DC fan.
Controls 2 front panel attenuators, crossover select switch for HPF, Normal and LPF
Indicator LEDs Five LED indicators per channel: Active, DC, Temp, Sig and ACL™
Protection Thermal, DC, subsonic, incorrect loads, under and over voltage.
Connectors Inputs: Dual Combination 1/4” XLR, Outputs: Three 4-pin twist-lock
connectors for 2 channels plus bridge.
Construction 18 ga. galvanized steel
Dimensions 3.5”x19”x 10.5” behind front panel + 0.6” for handle
Net Weight 5.54 kg (12.2 lbs.*)
Gross Weight 6.30 kg (13.9 lbs.)
Rated power readings made with BW: 20 Hz to 22 kHz. All power measurements made @ 120 VAC or 240VAC.
2 ohm steady state sine wave power is time limited by circuit breaker
*Net Weight does not include power cord.
CREST Pro-LITE 3.0: https://bit.ly/crestprolite3
Superb condition, very clean, works perfectly, zero issues
Price includes FedEx / UPS GROUND shipping in the CONUS ONLY
FOR SALE ONLY, NO TRADES
PayPal or Venmo payment accepted
PM with questions
SPECS below.
Thanks!
_____________________________________________________________________
Crest® Pro-LITE® 3.0 Specification Sheet
Rated Power Bridge 4 ohms 3640 watts 20ms repetitive burst / 3000 watts 1% THD @ 1kHz.
Rated Power Bridge 8 ohms 2000 watts 20ms repetitive burst / 1550 watts 0.15% THD @ 1kHz.
Rated Watts 2ch x 2 ohms 1820 watts 20ms repetitive burst / 1500 watts 1% THD both channels driven
@ 1kHz.
Rated Watts 2ch x 4 ohms 1000 watts 20ms repetitive burst / 900 watts 1% THD / 830 watts 0.15% THD,
both channels driven @ 1kHz.
Rated Watts 2ch x 8 ohms 540 watts 20ms repetitive burst / 500 watts 1% THD / 450 watts 0.15% THD,
both channels driven @ 1kHz.
Minimum Load Impedance 2 ohms
Maximum RMS Voltage Swing 71 volts
Frequency Response 20Hz - 28kHz; +0dB, -3.0dB at 1 watt.
20Hz - 20kHz 2ch x 2 ohms <0.5% @ 1350 watts at 20Hz increasing to 1380 watts at 20kHz, both
channels driven.
20Hz - 20kHz 2ch x 4 ohms <0.15% @ 800 watts at 20Hz increasing to 850 watts at 20kHz, both
channels driven.
20Hz - 20kHz 2ch x 8 ohms <0.15% @ 450 watts 20Hz increasing to 500 watts at 20kHz, both
channels driven.
Input CMRR > - 76dB @ 1 kHz
Voltage Gain x 75 (+37dB)
Crossover 100 Hz switchable 2nd order high pass and 3rd low pass per channel.
Crosstalk > -70dB @ 1kHz @ 250 watts power @ 8 ohms.
Hum and Noise > -100 dB, “A” weighted referenced to rated power @ 4 ohms.
Slew Rate > 12V/µs
Damping Factor (8 ohms) > 255:1 @ 20Hz - 1kHz @ 8 ohms.
Input Sensitivity 0.740 volts +/- 3% for 1kHz 4 ohm rated power, 0.710 volts +/- 3% for 1kHz
2 ohm rated power
Input Impedance 15k ohms, balanced and 7.5k ohms unbalanced.
Current Draw @ 1/8 960 (540) @ 2 ohms, 620 (320) @ 4 ohms, 400 (190) @ 8 ohms
power in VA (watts)
Current Draw @ 1/3 2070 (1310) @ 2 ohms, 1220 (700) @ 4 ohms, 740 (400) @ 8 ohms
power in VA (watts)
Idle Consumption 140VA, 60 watts.
Cooling Temperature dependent variable speed 80 mm DC fan.
Controls 2 front panel attenuators, crossover select switch for HPF, Normal and LPF
Indicator LEDs Five LED indicators per channel: Active, DC, Temp, Sig and ACL™
Protection Thermal, DC, subsonic, incorrect loads, under and over voltage.
Connectors Inputs: Dual Combination 1/4” XLR, Outputs: Three 4-pin twist-lock
connectors for 2 channels plus bridge.
Construction 18 ga. galvanized steel
Dimensions 3.5”x19”x 10.5” behind front panel + 0.6” for handle
Net Weight 5.54 kg (12.2 lbs.*)
Gross Weight 6.30 kg (13.9 lbs.)
Rated power readings made with BW: 20 Hz to 22 kHz. All power measurements made @ 120 VAC or 240VAC.
2 ohm steady state sine wave power is time limited by circuit breaker
*Net Weight does not include power cord.
