• TalkBass has been independent since 1998. Add your voice.
    Create a free account to reply to discussions, view embedded media, and browse with fewer display ads.
    Join free Log in
    Want zero display ads or expanded classifieds tools? Compare plans.

Advice on a router

#4
depending on what you plan to do with your router building basses, you will need to decide between 1/4" and 1/2" collet. 1/4" will usually be a smaller, less expensive router that i think are completely satisfactory for routing roundovers, truss rod channels, and pickups. If you want to get into routing the edge of your body smooth, you will most certainly need the bigger 1/2" routers. I actually enjoy the process of hand sanding the edges and since i dont make very many, 1/4" was good enough for me.
 
#5
If you go 1/2" then the router should also come w/a 1/4" collet- what's more, heavier IME=steadier & more resistant to *hiccups*& vibration in general. Along the *heavier is better* frame of mind(not claiming this as the Gospel, just my pref), Milwaukee, Porter-Cable & Bosch are nice; I don't like the feel of Ryobi & B&D(although DeWalt, a subsidiary/cousin of B&D, is quite nice).
 
#6
Thanks.

I only have shop experience (as in high school shop) with routers, but I remember doing good.

I am a tough and patient self learner, but I do like asking a bunch of questions online (I guess this negates the "self" part somewhat).

I hope you guys don't mind...

Thanks for the answers.
 
#7
I own this Ridgid:

Invalid Link Removed

I have been happy with it as a woodworker and a bass building hack. It comes with a 1/4" and a 1/2" inch collet and two bases (fixed and plunge). It is about 200 bucks new, but I see the Home Depot website has them reconditoned for 150. If that is more than you are interested in spending, Ryobi makes decent tools for the price. I have happily owned a Ryobi router. I would avoid anything cheaper than a Ryobi, though.
 
#8
bassteban said:
If you go 1/2" then the router should also come w/a 1/4" collet- what's more, heavier IME=steadier & more resistant to *hiccups*& vibration in general. Along the *heavier is better* frame of mind(not claiming this as the Gospel, just my pref), Milwaukee, Porter-Cable & Bosch are nice; I don't like the feel of Ryobi & B&D(although DeWalt, a subsidiary/cousin of B&D, is quite nice).
Click to expand...

yes the bigger routers can handle both bits. But routers are powerful tools man, i feel like i have more control over the smaller ones. personal preference...
 
#9
When I started out, I bought a good consumer model Bosch router and a Trend starter kit of 1/4" bits.

I discovered that those starter kits are ok for building simple furniture and bird tables, but its better to get decent bits as and when they are needed - you can then buy the exact size you need, and you wont waste time coming up with intricate jigs to make do with the cheapos.

EDIT: also, be aware that not all two flute bits have a bottom cut feature - dont try to plunge with those that dont! :eek:
 
#10
Look for an old Porter Cable 690 series with the fixed, plunge, and D handle bases. You should be able to get a good set up for less than $200ish.

For bits: CMT and Freud are the best quality and price out there.
 
#13
Thanks for the advice, Mikey.

I am afraid the shipping cost from Cinci will be a deal killer :)

I have started to look at the ads in CL. It's unfortunate that this economy is bad, but lots of contractors are going OOB and there is good pro and semi-pro hardware for not much right now.
 
#15
Gotta add, get good bits, make a plan before you turn it on, don't force the tool, turn the power off when setting up the router, and WEAR eye protection! A cheap bit can crack on you, and throw metal at your eyes at the speed of sound. . . .you, going "Eyaggggh!".

Public Service announcement>
 
#18
I have 2. A PC 3 1/4 in a Craftsman table and a Hitachi plunge. Both have the 1/2 inch collet. Using 1/2 inch bits are preferred since they are heavier and will do a nicer job, though you may need to use a 1/4 inch if the bit doesn't come in 1/2.

The best advice is to buy the best tools you can afford. I made the mistake of buying cheap stuff and it doesn't hold up well and you end up replacing it.

Good luck
 
#20
i have a bosch model 1617evspk kit. 1 motor with 2 bases....fixed and plunge. fantastic package. the fixed one stays in the table. for the table, i took out 1 extension wing of my table saw and replaced it with some countertop, and use the back of the saw's fence as a router fence. always pull the plug before you go near the blade....always. i use 1/2 inch bits, theyre just better made. and remember, you can spend a million on a tool, but the only thing that actually touches wood is the bit/blade...never go cheap with the bits
 

Latest posts

Top Bottom
Back