Post Yer Pedalboard - 23 Skidoo

[metalinthenight]

lovin that tone hammer!

 

[FuzzAddict]

Signal chain: Bass, Morley PWA2 Wah, Electronix Submarine Pre-amp, HAO Rust Ride distortion, Fulltone Bassdrive(Non-MOSFET) overdrive, EHX BBM fuzz, Mxr El Grande fuzz, EHX Bass synth, EHX Micro Qtron(planning on selling), ISP Decimator.
I usually put the Gt6b between the Submarine and the Rust Ride.
Planning on selling the Qtron, and then replacing it. Any ideas?

 

[isko]

Here's my pedalboard as of today

 

[megadan]

Finally, finally, finally got a) a pedal board and b) pictures of it!!

Chain: Turbo Tuner --> Micro POG --> Brown Dog -- Fatman --> Prunes & Custard --> VFB-2 w/ Polish Love in the loop --> Opto Stomp --> CEB-3 --> Memory Boy


Just 'cause:

 

[nodisco]

In studio

 

[s_mcsleazy]

Finally, finally, finally got a) a pedal board and b) pictures of it!!

Chain: Turbo Tuner --> Micro POG --> Brown Dog -- Fatman --> Prunes & Custard --> VFB-2 w/ Polish Love in the loop --> Opto Stomp --> CEB-3 --> Memory Boy


Just 'cause:

i think i have the same board/case as you

well i actually need to get another one cos im running outta space on mine

damn whammy, sounds amazing but takes up 4 spaces

 

[ase_one23]

In studio

i like it, nice and simple.

 

[G0rilla]

In studio

Nice and simple!
Greetings from Riga

 

[nodisco]

Thanks, guys!
And greetings from Tallinn to Riga.

 

[tom_ric]

my board

 

[king_xanadu]

any clips of the small close perhaps? i havent heard it on bass before.

 

[BruceBass3901]

my board

Is that the Ashdown Envelope Filter?

 

[rcubed]

Thanks, guys!
And greetings from Tallinn to Riga.

I've been to Tallinn but had to pass on Riga due to time constraints. I'll have to check it out next time.

 

[Valerus]

my board

nice setup!

 

[tom_ric]

hi guys thanks for the replys. sorry about my english, hope you"ll understand.

king_xanadu - i guess you ment the small clone, sorry, i have no clips, i actually have no idea how to do it.

brucebass - is is the ashdown envelope filter. i love it, it does what i need. it is big, and hard to dial. but i love the fact that it has an input volume and an output volume, which helps fixing lots of envelope filters problems (spikes, glitching etc.)

valerus - thanks man. i need to buy an expression pedal for my new pitchfactor in order to complete the board.

 

[BruceBass3901]

hi guys thanks for the replys. sorry about my english, hope you"ll understand.

king_xanadu - i guess you ment the small clone, sorry, i have no clips, i actually have no idea how to do it.

brucebass - is is the ashdown envelope filter. i love it, it does what i need. it is big, and hard to dial. but i love the fact that it has an input volume and an output volume, which helps fixing lots of envelope filters problems (spikes, glitching etc.)

valerus - thanks man. i need to buy an expression pedal for my new pitchfactor in order to complete the board.

I hear that the Ashdown pedals are very noisy? Your opinions on this?

 

[tom_ric]

I hear that the Ashdown pedals are very noisy? Your opinions on this?

my envelope filter isn"t noisy at all + its true bypass. few years ago when i was buying the filter, i played all ashdown's pedals, few minutes each, and i didnt noticed any noise problems.

 

[Bob C]

Ok, I couldn't wait. Here's an idea of what the my project board will look like when it is completed:

The signal path will go like this:

Bass - Planet Waves tuner - NS-2 (loop out) - Symetrix 501 - Pigtronix Disnortion (dirty output) - VT Bass - (loop input) NS-2 - SMMH (left input) / (clean output) - Octave Multiplexer - BSW - SMMH (right input) - M-80.

The left output (dirty) will go into an Ashly BP41 preamp running one channel of my Peavey IPR1600, and the M-80 (clean) will run the second channel. Each side will run one of my Tech21 B410 cabs; one filthy dirty and one fairly clean.

You can't see it very well, but there is a BBE Supa Charger under the 501.

As for the board, it's made out of 3/4" plywood, and I'm going to build an NYC Pedalboards-style lid/case for it. I'll spray it down with truck bed liner, and the top it all off with industrial-duty velcro.

I like it. You should build a space for your power amp in there too. How difficult will it be to stomp on the top shelf pedals?

 

[wrathofgod]

Here's my pedalboard as of today

whats that tiny pedal in the lower middle? seems to have a heart and the word small written on it.

 

[G0rilla]

I've been to Tallinn but had to pass on Riga due to time constraints. I'll have to check it out next time.

Contact me when you do it, friendly welcome and excursion guaranteed