quick pedal power 2+ question

[Rycebag]

will the pedal power be able to power a fulltone bass drive and aguilar tone hammer? ill also be powering 3 boss pedals too

 

[Ubersheist]

Add up the number of amps on your pedals. If your "power pedal" (not sure what that is) supplies more amps then the number of amps your pedals require, then it'll work no problem.

 

[Rycebag]

Add up the number of amps on your pedals. If your "power pedal" (not sure what that is) supplies more amps then the number of amps your pedals require, then it'll work no problem.

(voodoo lab pedal power 2+)

 

[Bassist4Eris]

Add up the number of amps on your pedals. If your "power pedal" (not sure what that is) supplies more amps then the number of amps your pedals require, then it'll work no problem.

Sorry, but I don't think this makes much sense.

The two specs you want to find on your fulltone bass drive and aguilar tone hammer are the voltage requirements (expressed in Volts, or V) and the draw (expressed in mA's.)

Most of the outputs on the Pedal Power can only supply 100 mA. Outputs 5 and 6 can supply 250 mA. As long as the pedals require LESS than these amounts, they can be powered off of these jacks. Assuming the voltage requirements match up as well.

 

[Adrisss]

The Tone hammer requires 18V if I remember well, so you'll have to couple 2 outputs of the PP2+ with a "Y" cable to get these 18V

So that's :

3 boss pedals : 3 of the 9V outputs
Tone Hammer : 2 of the 9V outputs

So thats 3 outputs still available for your last pedal and maybe more !

Also I think there are 2 outputs that can be switch between 9V and 12V.

 

[willbassyeah]

What boss pedal did you use? If i remember correctly most boss pedal only use less than 50 milli amp. Most of their analog only used 10-11 milli amp. So you can actually daisy chain one output to power all your boss pedal. Btw this link has most of the amperage listing http://www.diago.co.uk/powerstation_compatibility.html

 

[Adrisss]

Quite a usefull link !

 

[Ubersheist]

Sorry, but I don't think this makes much sense.

The two specs you want to find on your fulltone bass drive and aguilar tone hammer are the voltage requirements (expressed in Volts, or V) and the draw (expressed in mA's.)

Most of the outputs on the Pedal Power can only supply 100 mA. Outputs 5 and 6 can supply 250 mA. As long as the pedals require LESS than these amounts, they can be powered off of these jacks. Assuming the voltage requirements match up as well.

Oh. I was assuming they were all 9v with standard sized power adapters. If there are different voltages, then my other post is hogwash.

 

[Rycebag]

Also if i leave the DIP switches on the bottom in the normal position ill be able to use all the outputs for 9V boss type pedals right?

 

[Adrisss]

You got it. You can have 8 standard 9V. But yet you can power up a lot more than 8 pedals since most won't drain all of the 100 ma of each output. And there are 2 of them allowing up to 250 ma if I remember well !

 

[lowfreq33]

Don't forget the accessory outlet on the back. I have ten pedals and a wireless on my board with the PP2+. The accessory outlet goes to the tuner which is daisy chained to two boss pedals.

 

[govan]

Hi friends!!!
I have a question
i Have a twin pedals Boss Rc20xl 9v (125mA) and aguilar tone hammer pedal /Direct box 18v (300 ma i think so)
Could you help me about which power supply i can buy? i have a great dude my friends
about Iso 5 voodo lab or vodoo lab PP2+
I'm from Peru and the voltage is 220v
please my friends
i'd like to help me!!!
Thanks for everything

Govan