Recent content by fathom66

Thanks everyone. This really helps. I know the mackie doesn’t add the “growl” I spoke of but I did like the cleaner tone through my drummers PA… I never really get to hear the FOH sound from my BDDI first hand but on different live recordings it sounded pretty good…like I said I’ve ran this way...

Bass——tuner—- darkglass compressor—-loop switch (for wah)….distortion… sansamp…. Amp I use the Sansamp XLR out to FOH and use the sculpted tone into the amp too… but seeing how the mackie sounded at practice in the mixer was monster… just wanted to see if there was a way to keep my stage tone...

Ok so you’re saying use that parallel output and put into the input of my mackie and use THAT XLR out to the mixer… the other effects that I use will still send the signal from the mackie into front of house… while at the same time… I can use the “regular” output to my amp? I’ve always wondered...

Got a question… I’ve been in this setup for years regarding my pedalboard for my live setup…. Amp—- sansamp—-distortion pedal—- wah (loop switch ) compressor—- tuner—-bass…. I normally use the sansamp to boost my tone for the amp and use the XLR out to the mixer…. Now during practice I forgot...

Got a question… I’ve been in this setup for years regarding my pedalboard for my live setup…. Amp—- sansamp—-distortion pedal—- wah (loop switch ) compressor—- tuner—-bass…. I normally use the sansamp to boost my tone for the amp and use the XLR out to the mixer…. Now during practice I forgot...

Well I wound up getting a Fender rumble 115 to match… the 4x10 is 500watt continuous/ 1000watt program… the 115 is 300watt continuous/ 600watt program… both at 8ohms… my Hartke LH500 head is 500watts with two 8ohm outputs… I do have a Hartke LH1000 also but for some reason I feel the 115...

I currently have a Hartke lh500 running into a newer Fender Rumble 4x10 cab as my smaller setup… the Hartke has two 8ohm out puts in which I run a single cable from the head through my cab, which is also 8ohms… now I have the opportunity to gain a Mesa diesel 1x15..two things: I can run the...

Ok makes sense... like I said it was just a thought

Anyone out there use BOTH on their pedal board (both on of course)... any thoughts? Obviously it’s up to me but just wanted to hear some positives and negatives

would it hurt to run a xlr from my sansamp BDDI from my pedal board, which is obviously common.... but run a cable from my head xlr to say my behringer B215D 15” top/monitor... sometimes I use my smaller Fender Rumble 350 or my Hartke 5410c combo and would like a little more stage volume...

Sorry for the late response ... no I’m good. I actually figured out the issue. I had a bad tube in the head. It was stock with the “cheapie” sovtek tube... put a jj electronics one and my issue hasn’t resurfaced... if anything I’ll have to check speakers for volume now but it no longer cuts out

my total ohm is 4.... that’s what I’m reading on my meter at each connection while still plugged... in order to read individual I’ll have to unsolder those connections

I would have thought the same thing but I ohmed out the speakers myself which were all pretty much soldered in place at the connections and read at 4ohms... which means all are in series.... nothing blown that I could tell.

I’ve had issues with the head portion of this combo, which is basically a lh500 paired with a 410 Hydrive cab. Now I’ve basically given up on this head but I was wondering if I can bypass the head completely and unplug it (basically has a speaker cable connecting the two in the combo) ... then...

hey guys, just need some insight. My normal set up is as follows HARTKE 5410c combo----sansamp bass di---mxr m180 compressor---korg pitch black tuner----digitech drop tuner---BASS Seeing that I wanted to doctor up a few things or even add for certain tunes so I have this on standby but having...