Fender Rumble Club

[JakobT]

What the heck is that thing called and where can we get one? Thanks!

Invalid Link Removed

 

[buldog5151bass]

Yeah, but if you're replacing them you don't care if you destroy them with pliers.

Or just wrap a rubber band around a few times before you get out the pliers.

 

[Linnin]

What the heck is that thing called and where can we get one? Thanks!

Knob Puller from StewMac!
Invalid Link Removed

 

[Raymundo49]

What the heck is that thing called and where can we get one? Thanks!

Try this! https://www.amazon.com/Healifty-Gui...309&sr=1-7-catcorr&keywords=Knob+remover+tool

 

[Kipp Harrington]

Knob Puller from StewMac!
Invalid Link Removed

Thanks Linnin!

 

[Kipp Harrington]

Try this! https://www.amazon.com/Healifty-Gui...309&sr=1-7-catcorr&keywords=Knob+remover+tool

Thanks Raymundo49!

 

[Raymundo49]

Thanks Raymundo49!

No problem! Good luck!

 

[Jacob J]

Have had my Rumble 500 combo since June 2015 and it's never let me down once. Really like the portability and sound of this thing. Here's how it sounds like with my Classic 50's Lacquer P (bare stock) hooked straight to it and the OD circuit engaged:

 

[Linnin]

Have had my Rumble 500 combo since June 2015 and it's never let me down once. Really like the portability and sound of this thing. Here's how it sounds like with my Classic 50's Lacquer P (bare stock) hooked straight to it and the OD circuit on:

Is Groovy! And XLR out straight to the board. Well Done.

 

[bdplaid]

So... do you think it would be a good idea for me to order some of the ones you got? My Rumble head is only about 8 months old.

My first set were sticky right out of the box. The dealer ordered new ones and put them on, and a couple of years later they were super sticky again. So, I'd replace them with whatever kind of knobs you like. I think you can get cupcake knobs from different manufacturers that will keeps the same look, but (hopefully) not go all sticky down the line.

 

[bdplaid]

Would you post a pic of how these new knobs look on your Rumble, please? Thanks!

I already did, a lot of posts ago. if i can find it (unlikely) I will repost.

 

[bdplaid]

Knob Puller from StewMac!
Invalid Link Removed

I have one of these and it did't work - the knobs were too close to the amp face. I think I wrapped a small screwdriver with tape and gently pried them off. No damage. But work slowly and carefully.

 

[bdplaid]

Would you post a pic of how these new knobs look on your Rumble, please? Thanks!

 

[bass hed]

 

[bass hed]

View attachment 3311856 View attachment 3311856

Got this nice 2x10 cab the other day, boy does it rock! Replaced my old fender 4x10 which was probably about 60+lbs heavier lmao. Loving life!!

 

[Kipp Harrington]

View attachment 3311846

Thank you bdplaid! I like the idea of using the red knobs for the drive and level.

 

[bdplaid]

Thank you bdplaid! I like the idea of using the red knobs for the drive and level.

 

[west al]

Pop-Cicle sticks flat, on either side of the shaft, and pull up

 

[MCF]

Got this nice 2x10 cab the other day, boy does it rock! Replaced my old fender 4x10 which was probably about 60+lbs heavier lmao. Loving life!!

Nice bass too, by the way.

 

[LennyJ]

Hello All,

I saw a post where someone was chaining 2 rumble combos together I think thru the effects loop.

Can anyone help me with this to find that post or tell me if it can be done.

Thanks

LennyJ