Fender Rumble Club

[Droopy_TX]

Can the Rumble Studio USB Audio Out Interface be used on an iPad? I mean, to record on Garage Band , DAW etc. Has anyone tried that? Does it work?

Timo, I tested this today, too. The answer is, "Yes."

I have a Rumble Stage 800. The Stage 800's USB audio out is the same as the one on the Studio 40. To connect it to the iPad you need an adapter plug that converts the USB-A end of the cable coming from your Rumble Studio 40/Stage 800 to the plug receptacle type your iPad has. The receptacle could be the original 30-pin plug or the "lightning" plug on the iPads, or the new USB-C plug on the iPad Pros. These are available from Apple and other manufacturers. Some have additional ports that let you also connect a power cable to power your iPad simultaneously.

I connected my Stage 800 to my iPad Pro via a USB-A-to-USB-C adapter. I had the amp on with GarageBand running on the iPad and open to the Audio Recorder instrument. GarageBand immediately asked me if I wanted to use the amp as my audio source. It setup the track to use the input device and turned on monitoring. From there, everything worked as you'd expect.

I created a quick demo project using the Smart Drums, and recorded 3 bass tracks using effects on the Stage 800 to make sure they were recording, too. It worked perfectly. Here's a link to the GarageBand test project in DropBox.

Hope this helps.

 

[John Stephen]

Timo, thank you for asking the question and Droopy, thank you for the answer. I am just starting to try to dip my toes into home recording, and the going is tough. So Droopy, I take it from your post that you did not need an "audio interface" gizmo. Your instrument was plugged into your Rumble amp, and the Rumble amp was plugged into your iPad, and your GarageBand was able to recognize it. Do I have that right?

 

[Droopy_TX]

Timo, thank you for asking the question and Droopy, thank you for the answer. I am just starting to try to dip my toes into home recording, and the going is tough. So Droopy, I take it from your post that you did not need an "audio interface" gizmo. Your instrument was plugged into your Rumble amp, and the Rumble amp was plugged into your iPad, and your GarageBand was able to recognize it. Do I have that right?

Yes, John, that is correct.

The USB output from my Rumble Stage 800 was plugged directly into my iPad using the normal USB-mini-to-USB-A cable, which was converted via the USB-A-to-USB-C adapter to make it compatible with my iPad Pro. No other hardware was needed.

I'd never done this before because I usually record on my Macbook. So, I was intrigued and curious.

I'm very pleasantly surprised that it easily worked so well.

 

[John Stephen]

Great, thanks so much for the info.

 

[TimoBatis]

Yes, John, that is correct.

The USB output from my Rumble Stage 800 was plugged directly into my iPad using the normal USB-mini-to-USB-A cable, which was converted via the USB-A-to-USB-C adapter to make it compatible with my iPad Pro. No other hardware was needed.

I'd never done this before because I usually record on my Macbook. So, I was intrigued and curious.

I'm very pleasantly surprised that it easily worked so well.

Im thankful you did the test !!,, that's great news for me, and Im sure for some other users as well. I do have a camera adapter for iPad that converts USB-A to lightning (my kid uses it to connect his Alesis drums to the iPad). I'm just a step away from getting a Rumble Studio and I wanted to make sure. Thanks again.

 

[John Stephen]

I've got the regular Rumble 40, not the Studio version. So my amp doesn't have a USB port, just the usual XLR line out. On a whim, I just googled XLR-to-USB adapter and found that they actually exist.

https://www.amazon.com/Shure-X2U-XLR-to-USB-Signal-Adapter/dp/B001PPXFAG

I wonder if this would enable me to plug my Rumble 40 into my laptop or iPad. Anybody tried this? Anybody familiar with these? Though for $99, I could buy an audio interface for not much more than that.

 

[Tex Bass]

[QUOTE="John Stephen, post: 23938221, Though for $99, I could buy an audio interface for not much more

Agreed. I just got a Scarlett Solo for $109 and it has both instrument and mic inputs along with free DAW software and plug-ins

 

[Bottom Octave]

I've got the regular Rumble 40, not the Studio version. So my amp doesn't have a USB port, just the usual XLR line out. On a whim, I just googled XLR-to-USB adapter and found that they actually exist.

https://www.amazon.com/Shure-X2U-XLR-to-USB-Signal-Adapter/dp/B001PPXFAG

I wonder if this would enable me to plug my Rumble 40 into my laptop or iPad. Anybody tried this? Anybody familiar with these? Though for $99, I could buy an audio interface for not much more than that.

While there is a range of 40 dB on the mic level control of the Shure XLR-to-USB adapter, the line level output of the Rumble may overload the input unless you keep it very low. The Shure device is designed for mic levels, which are much lower. Let us know what you decide to get and how it works out for you.

 

[Droopy_TX]

...I wonder if this would enable me to plug my Rumble 40 into my laptop or iPad. Anybody tried this? Anybody familiar with these? Though for $99, I could buy an audio interface for not much more than that.

John,
I have an older Apogee Jam. It is nominally functional, certainly portable, and easily powered from the USB bus. The Shure unit you cite looks nicely equipped, with its phantom power, separate “zero-latency” monitor level, etc.. I like the fact that it uses a standard USB cable (unlike the Jam’s proprietary cable). I don’t like the fact that it only accommodates XLR connections (i.e. it’s not a combi-plug). There will be times that you just want plug your guitar in without the amp. (Similarly, the Jam only accommodates 1/4”.)

In general, although I do appreciate their portability, and always carry my Jam with me when I’m out, I am not a fan of inline audio interfaces. My main issue is the “touchiness” of the little level dials. Also, I kind of suspect the preamp quality of those small units.

My main audio interface is the Behringer UMC404HD. In terms of bang-for-buck, it’s great. I’ve used it for years, and have had no issues with preamp quality; and it’s got all the connectivity features I need. The controls operate smoothly and solidly. Its “little sibling”, the UMC202HD, has the same input features but just 2 inputs/outputs for $120 USD.

Both also have input signal switching for line or instrument (high impedance), and a pad feature for “hot” signals. It’s not clear to me whether the Shure interface can accommodate a line level signal such as the signal coming from the line out on an amp. That might be a dealbreaker.

I’m not trying to sell you on the Behringer; but, rather, to illustrate the greater flexibility and capability of the “desktop” units. Being able to accommodate both plug types and any signal level is crucial to me. Also, 2 or more inputs gives you added functionality of simultaneous recording (e.g. bass and guitar, guitar and vocals, etc.). And, most of these smaller “desktop” interfaces (definitely the Behringer units) can run off USB bus power as well as AC power. So, they’re still fairly portable.

If it were me, I’d spend just a little more for a lot more functionality.

Again, hope this helps.

 

[John Stephen]

Thanks everybody, I appreciate all of your input and thoughts on this. Having thought about it some more, and reading your posts, I’m going to get an audio interface. The adapter thing indeed has too many limitations, as you’ve pointed out. Will let you know how it goes, and thanks again.

 

[SoulReflection]

Here's another way to pass some time...

Your Favorite Bassist of the '60's Era is?

 

[G-Dog]

I have a Fender Rumble 500

And, @Jason Schulhz, you are now member #1215 in the Fender Rumble. Congratulations and welcome to The Club in particular and to TalkBass in general. Make yourself at home here and in the Rumble Club Wiki page, linked in my signature, where there's Rumbling info galore, including the Rumble Club TONE POOL of settings you may try and/or contribute to. The Rumble 500 combo is an exceptional value in bass amps today. I've been thrilled with mine for nearly 6 years now!

Please tell us about yourself, your bass journey and your Rumble quest. We'd love to know more of your story. And feel free to ask anything of us, too. But always please do . . . .

Rumble On!
.​

 

[John Stephen]

Here's another way to pass some time...

Your Favorite Bassist of the '60's Era is?

Now there's one that I could spend an hour or three on.

 

[SoulReflection]

Now there's one that I could spend an hour or three on.

You are welcome to!

 

[LiquidSword52]

Adding mine to the mix. Fender Rumble 40 V3. More power than I need as someone learning the hobby just for home, but was sold on its features. I think This Bass Buzz video finally sold me.

I do find myself turning the Bass and Low mids down a bit, but that's the beauty of having options. Still working on a preferred tone (lots of variables to play with).

 

[RmbleRightously]

.
Attention: Rumble Club Wiki Edit Alert!

Thank you, @dcgriggs79 and @RmbleRightously, for sharing your cosmetic makeovers of your Rumble combos! griggsy, your thread of your now Blackfaced Rumble Stage 800, and Rmble, your post of your now cream/oxblood Rumble 500 combo, have both been linked on the Rumble Club Wiki page near the middle of the Rumble Modifications section, with other mods. These are great examples of a fun, and beautiful, amp cosmetic makeovers that are sure to be the envy of many a bassist.

Thanks, griggsy and Rmble, for your sharing.

Rumble On!​

.

just wanted to throw an updated photo up here since I finished my modification project. Pretty happy with the results! Huge thanks to the velcroed removable grill mesh, these amps make it easy for diy mesh/screen customization as well as painting modifications.

 

[SoulReflection]

View attachment 3813840 View attachment 3813840

just wanted to throw an updated photo up here since I finished my modification project. Pretty happy with the results! Huge thanks to the velcroed removable grill mesh, these amps make it easy for diy mesh/screen customization as well as painting modifications.

Nice stuff here...

 

[G-Dog]

Adding mine to the mix. Fender Rumble 40 V3. More power than I need as someone learning the hobby just for home, but was sold on its features. I think This Bass Buzz video finally sold me.

I do find myself turning the Bass and Low mids down a bit, but that's the beauty of having options. Still working on a preferred tone (lots of variables to play with).

View attachment 3813534

And, @LiquidSword52, you are now member #1216 in the Fender Rumble. Congratulations and welcome to The Club in particular and to TalkBass in general. Make yourself at home here and in the Rumble Club Wiki page, linked in my signature, where there's Rumbling info galore, including the Rumble Club TONE POOL of settings you may try and/or contribute to. The Rumble 500 combo is an exceptional value in bass amps today. I've been with mine for nearly 6 years now!

Please tell us about yourself, your bass journey and your Rumble quest. We'd love to know more of your story. And feel free to ask anything of us, too. But always please do . . . .

Rumble On!
.​

 

[Sparuto]

I got this rumble 100 a while back and I am always playing her with that vintage button on...and through my trusty P it is heaven to my ears. Any chance there’s still room left for a self professed Fender nut like myself? I’d love to be a member!

 

[G-Dog]

View attachment 3814255
I got this rumble 100 a while back and I am always playing her with that vintage button on...and through my trusty P it is heaven to my ears. Any chance there’s still room left for a self professed Fender nut like myself? I’d love to be a member!

Affirmative, Spar! @Sparuto, you are now member #1217 in the Fender Rumble Club. Congratulations and welcome. Please make yourself at home. That's a lovely Rumble 100. Pleaase tell us how it came to be for you.

But, always remember to. . . .

Rumble On!
.​