My brother sent me a reverb "how to pick dirt for bass" link this morning: It's OK, but I'm pretty pissed that they feature an opamp muff. Kinda like featuring an SG when talking about les pauls.
TalkBass has been independent since 1998. Add your voice.
Create a free account to reply to discussions, view embedded media, and browse with fewer display ads.
Join free Log in
Want zero display ads or expanded classifieds tools? Compare plans.
My brother sent me a reverb "how to pick dirt for bass" link this morning: It's OK, but I'm pretty pissed that they feature an opamp muff. Kinda like featuring an SG when talking about les pauls.
My point is that op amp muffs are a different circuit, using op amps rather than transistors and one less gain stage. There’s nothing wrong with them, just not representative of muffs.
Edit: If anybody needs me, I’ll be outside, yelling at some clouds.
Dang we go in spurts here. Can't keep up hahaha!
@cornfarmer totally get it. That's the whole reason I turned down a paint job at Tesla for BASF. Pay would be great, but not really for Cali.

As long as it's not memory foam or any type that won't spring back. The foam is acting as a spring, a counterbalance to the, screws that are 'pushing' the pickup into the body of the bass. Does any of that make sense? I have a severe case of "2pm on Friday brain drain"Does it matter what kind of foam goes under a pickup?
Interesting! Share something when you feel ready!!Do any Denver folks know any singers? Ours quit, which wasn’t a big surprise because he is way too busy. We have music recorded for 7 songs. The sound we are going for is like a mix of Drive Like Jehu, Fugazi, Shellac, Unwound, Melvins, Cloakroom. So not traditional metal vocals but more in the post hardcore world.

Does it matter what kind of foam goes under a pickup?
Buuuuuut... Lightweight cabs don't "vibrate" or "move" when played really LOUD? I know I'm doing philistine physics but I hope my doubt is not too stupidI use a Barefaced Super Twin 212. They are a custom driver in a highly engineered enclosure so they are hyper efficient, durable, have powerful excursion, and good off axis tonal quality. They are built more or less like PA speaker cabs, which also means they are flat response. The lack of a tonal character can be a little off putting.
That said, it is rated at 1200w and will compete in terms of sheer volume with an Ampeg 810. All in a 3 ft high enclosure that weighs maybe 35 lbs.

No they don'tBuuuuuut... Lightweight cabs don't "vibrate" or "move" when played really LOUD? I know I'm doing philistine physics but I hope my doubt is not too stupid![]()

However, the engineering could be as simple as putting rubber feet on the cabs so that they can't move![]()


Well built cabs shouldn't. If they are properly build they are stable platforms for projecting the sound of the speakers. One of the benefits of a fridge is they are very well constructed, so the use of air pressure is efficient. Smaller super cabs are the same, just better engineered for weight. If you where to knock on the side of my Super Twin you would hear no reverberation at all.Buuuuuut... Lightweight cabs don't "vibrate" or "move" when played really LOUD? I know I'm doing philistine physics but I hope my doubt is not too stupid![]()
My greenbiy dually weighs like 60 lbs. It wont move away. Especially with the 100 something pound verellen on the top.
Those old school shops might have it. Bring it with you if need be. They'll know exactly where to find it if they are anything like the shop near me. Otherwise you can look up the value and order them online. Either way, they are cheap.Bass issues solved! It was all a blend pot intermittently crapping out (besides a preamp dying). The lug is loose and wiggles. Currently using electrical tape to keep the wire and lug tight.
So, where do I go to get a new one? Would typical electronics stores have one, or is online better? I have a local old-school electronics shop about 20 min away, but it's above my head what most of that is. It's col to go looking though.