• TalkBass has been independent since 1998. Add your voice.
    Create a free account to reply to discussions, view embedded media, and browse with fewer display ads.
    Join freeLog in
    Want zero display ads or expanded classifieds tools? Compare plans.

Squier Vintage Modified Precision V: who's got one?

So you thought it was dark with the 250k, and changed to the 500k? If so, I'll just leave it alone :) Remember, I've just got the 500k volume pot, with the Stellartone Tonestyler replacing the tone pot, so my harness is probably different ...

Thanks!
Mine was a special case- stock pots were both beyond the outer edge of tolerance, down around 200K. Bled quite a bit of treble off.

I was re-wiring for a PJ install, and thought “what the heck, I’ll try some 500K’s”.

More proof that what you think is caused by mojo or lumber, could be some other factor that you overlooked...
 
OK...NBD for me! Finally located a 2013 VM P bass 5 string that looks mint. Can't wait to play it. I have read all the way through this thread and found a million opinions, but I will ask anyway. The first 'mods' that I plan are to lightly sand down the finish on the back of the neck, and new strings. For the classic 'P bass' sound, what strings do you recommend. Since I'm a newby please give brand, model and sizes of strings if you can. Thank you!
Squier V.jpg
Screen Shot 2019-04-30 at 8.55.34 AM.png
Screen Shot 2019-04-30 at 8.55.12 AM.png
 
OK...NBD for me! Finally located a 2013 VM P bass 5 string that looks mint. Can't wait to play it. I have read all the way through this thread and found a million opinions, but I will ask anyway. The first 'mods' that I plan are to lightly sand down the finish on the back of the neck, and new strings. For the classic 'P bass' sound, what strings do you recommend. Since I'm a newby please give brand, model and sizes of strings if you can. Thank you!View attachment 3402251 View attachment 3402252 View attachment 3402253

Those are two good mods! I currently run DR Low-Riders on mine for church, but for flats I would recommend the DR Legend Flatwounds, which I have used, or the Labella 760FL-B, which seem to garner alot of praise.

Following is a good thread on flatwound options -

La Bella 760FL vs. DR Hi-Beam Flats vs. Fender 9050ML vs. TI JF344
 
  • Like
Reactions: Rezdog
P-Basses have seen and done it all.

What you call the “classic P-Bass sound” depends on your demographic.

If you like 60’s and early 70’s pop (Joe Osborne, Carol Kaye), a pick and a dead set of Labella or Fender flats is just the ticket. Careful EQ is required to minimize the pick noise.

For Motown a la Jamerson, keep the flats and go finger-style. Roll the tone back at least half way.

Classic rock is all over the place. Finger-style with dead flats and the tone wide open for a sharp, flat thunk will get you Peter Cetera with Chicago, early Doobie brothers, etc.

A lot of harder rock was performed while beating pretty hard on a set of Rotosound stainless rounds. Mild amp distortion is welcomed.

Punk should always be played on a P-bass with nickel rounds and a nylon pick. A long strap (knee level or lower preferred) and maximum attitude are mandatory.

Nylon tapes are good for jazz, and also give a nice pseudo-acoustic vibe for unplugged sessions.

New Wave a la Joe Jackson and Elvis Costello is usually rounds and a pick, with scooped mids and just a touch of crunch up top...
 
Last edited:
Here's mine. I got it a couple years ago. I added DR Highbeams, an Omega bass bridge, made a brass nut for it, installed cts pots with a 100mf pio cap, Fender barrel knobs, switchcraft jack, sanded, restained and cleared the headstock and gave it a thorough set up. Next are pickups but havent decided which ones.
 

Attachments

  • 20190219_200530.jpg
    20190219_200530.jpg
    496.2 KB · Views: 140
  • 20190219_200519.jpg
    20190219_200519.jpg
    557.4 KB · Views: 151
  • 20190219_200509.jpg
    20190219_200509.jpg
    450 KB · Views: 143
Here's mine. I got it a couple years ago. I added DR Highbeams, an Omega bass bridge, made a brass nut for it, installed cts pots with a 100mf pio cap, Fender barrel knobs, switchcraft jack, sanded, restained and cleared the headstock and gave it a thorough set up. Next are pickups but havent decided which ones.
Nice! That bridge is burly.
 
  • Like
Reactions: jaypee
Nice! That bridge is burly.
The Omega IS a nice bridge but the Hipshot Kickass is nicer, with the adjustable spacing.
Omega:
[Invalid or Expired Link Removed]

Hipshot:
[Invalid or Expired Link Removed]

I went with the USA fender deluxe (non high mass) and drilled for String through (btw don't bother with string through)
Invalid Link Removed
 
The Omega IS a nice bridge but the Hipshot Kickass is nicer, with the adjustable spacing.
Omega:
[Invalid or Expired Link Removed]

Hipshot:
[Invalid or Expired Link Removed]

I went with the USA fender deluxe (non high mass) and drilled for String through (btw don't bother with string through)
Invalid Link Removed
Truth be told, if I were to do it again I would go with the Hipshot.
 
  • Like
Reactions: /\/\3phist0