• TalkBass has been independent since 1998. Add your voice.
    Create a free account to reply to discussions, view embedded media, and browse with fewer display ads.
    Join freeLog in
    Want zero display ads or expanded classifieds tools? Compare plans.

The Sushi Box FX Secret Society

View attachment 4501172
Fluffy Kitten is all high end grit and gain. Without messing with the trim pots yet, I tossed it in a filter FX loop to dial in low end with it. Sounds great and the Sashimi paired can really doom.
You're telling me.. this is where I have mine I'm loop. I do notice the higher the gain the more low frequencies come through. The Sashimi isn't heavy fuzz? I like a nice consistent clip, almost synth
20211211_143627_remastered.jpg
 
What would be the effect on replacing the stock tube in a Partical,Accellerator with a Nos JAN Phillips 12AT 7 ?

The stock Jj seems microphonic and I have a couple of 12ax ay and at 7's laying about. Not wanting distortion...

If you're looking to lower voltage gain, both 12AY7 and 12AT7 will work; personally I think AY is usually a better lower gain replacement for an AX than an AT is.
12AT7 have much higher transconductance and anode resistance than 12AX7s have.
12AY7 have pretty similar transconductance and resistance to 12AX7, just with much less voltage gain.

But if you have both, feel free to try both and see which you like the sound and feel of best; both are compatible and both will lower gain.

Jack
 
What would be the effect on replacing the stock tube in a Partical,Accellerator with a Nos JAN Phillips 12AT 7 ?

The stock Jj seems microphonic and I have a couple of 12ax ay and at 7's laying about. Not wanting distortion...
Yeah I would agree try both and see what sound you like. Either one will work fine, I've heard of people using both, comes down to which one sounds like what your ears want.

You're telling me.. this is where I have mine I'm loop. I do notice the higher the gain the more low frequencies come through. The Sashimi isn't heavy fuzz? I like a nice consistent clip, almost synth
View attachment 4501507
Yup increasing gain on Fluffy Kitten adds low end. Black Eye is the same way.

Sashimi can get some lovely fuzz tones, but it sounds like it wouldn't be what you're looking for. Fuzz Factory has always been one of my favorite fuzzes on guitars for the thick, saturated glitchiness with synth-like qualities like you said. Sashimi doesn't do that.
 
  • Like
Reactions: labeledbass
So last week Sunday I filled in at a gig and brought my small board with my PAX on it.

I have a one spot and daisy chain my PAX with a Bass Fly Rig. When I was setting up to plug in power I noticed a BDDI on the ground and unwittingly took power from the BDDI and daisy chained my board with a Tech 21 300ma 9 volt PS. I didn’t realize until after the gig, about 5 hours later.

The board performed flawlessly as I was using IEM’s. So I have a question. I am wondering if a Sushi pedal like the PAX, UA, or finally can be powered with a 300ma 9 volt PS? I know it draws high ma at warm up, but levels off to 250ma or so when warmed up. Will a 300ma PS just take a little longer to warm up and level off to be used efficiently?

Am I just lucky with this one off goof?
 
View attachment 4501172
Sashimi fuzz doesn't have a ton of hair but makes up for it with a lot of body. It is kinda like a Blueberry OD in that sense.

Fluffy Kitten is all high end grit and gain. Without messing with the trim pots yet, I tossed it in a filter FX loop to dial in low end with it. Sounds great and the Sashimi paired can really doom.
I get that. The sashimi is also not noisy. That’s the best part. It’s smooth across the gain curve without hiss.
 
You're telling me.. this is where I have mine I'm loop. I do notice the higher the gain the more low frequencies come through. The Sashimi isn't heavy fuzz? I like a nice consistent clip, almost synth
View attachment 4501507
Sashimi is not a heavy fuzz. It’s really smooth and reminds me a little of my Bray. It's not heavy clipping or spitty at all. Think 60s or early 70s FF. My opinion. There is a good tube thickness to it. The demos online are pretty much what you get. I have been using mine with guitar too and was able to dial in a Texas blues tone pretty close.
 
Last edited:
I think I am so used to silicon clipping that I think Velcro when I hear fuzz. The germanium chips have more of a heavy blossom to them. Big body tubey sound without farting out.
Yep. I have a lot of fuzz pedals, dozens. The Sashimi is not velcro ripping. When you think about fuzz there are so many different kinds that are really nothing alike. The Sashimi is in my opinion closer to a Dallas Arbiter type sound, it's not a muff sound, it is not a heavy clipping. I like heavy fuzzes too. But this is less gritty, more smooth, old school fuzz style. Think classic germanium-like but without the loss of bass. I think Mr. Box said at one point it wasn't for everyone, I think that's true with most fuzz pedals because there is so much variation.
 
So last week Sunday I filled in at a gig and brought my small board with my PAX on it.

I have a one spot and daisy chain my PAX with a Bass Fly Rig. When I was setting up to plug in power I noticed a BDDI on the ground and unwittingly took power from the BDDI and daisy chained my board with a Tech 21 300ma 9 volt PS. I didn’t realize until after the gig, about 5 hours later.

The board performed flawlessly as I was using IEM’s. So I have a question. I am wondering if a Sushi pedal like the PAX, UA, or finally can be powered with a 300ma 9 volt PS? I know it draws high ma at warm up, but levels off to 250ma or so when warmed up. Will a 300ma PS just take a little longer to warm up and level off to be used efficiently?

Am I just lucky with this one off goof?
It really comes down to how the power supply is designed. Some (like 1spot) have a "soft" limit and will actually let you pull a little above the rated current. Others have a "hard" limit and will sag the voltage when presented with a heavy load. The worst (though I totally understand from a design perspective) is when they complete shut down on a heavy load, so the pedal never gets a chance to warm up.
 
Right, prototype board for that one and the Tweed Deluxe are sitting on my bench right now. Just need tube sockets and some pots and jacks and they're ready for a test, probably get to that sometime this week after everything is finished for November.
After watching the Beatles documentary, I'm really GASsing for a Hofner and a Bassman ..
 
Yep. I have a lot of fuzz pedals, dozens. The Sashimi is not velcro ripping. When you think about fuzz there are so many different kinds that are really nothing alike. The Sashimi is in my opinion closer to a Dallas Arbiter type sound, it's not a muff sound, it is not a heavy clipping. I like heavy fuzzes too. But this is less gritty, more smooth, old school fuzz style. Think classic germanium-like but without the loss of bass. I think Mr. Box said at one point it wasn't for everyone, I think that's true with most fuzz pedals because there is so much variation.
Curious if you've tried a 3Leaf Doom2, and how you'd compare it up against the Sashimi. One of these seems easier to get than the other, these days.
 
  • Like
Reactions: Killing Floor
Curious if you've tried a 3Leaf Doom2, and how you'd compare it up against the Sashimi. One of these seems easier to get than the other, these days.
I've never had the 3Leaf because I am an incomplete shell of a human. Can't honestly compare. I've heard them, they may be a little darker but I really am basing it off hearing other people play. I do have the Octabvre v3 so I'm not completely worthless. Seems like the Sashimi and Doom2 are both hard to get right now. But from what I can tell The Box isn't trying to go out of biz, seems like Spencer is done for now. Hope I am wrong.
I do know the Sashimi demo is basically what I get on bass and it sounds really good on guitar too.
 
At my old job they used to have a Christmas open house every year where families could come on the base and tour some of the facilities, and groups would prepare little presentations and giveaways for people that would come through. The main circuit design group that housed the electronics tech shop always did some kind of christmas tree ornament circuit board, and they would run them through the pick and place machine so people could see them get put together then they would hand them out to everyone. I always thought to myself "man, that's a cool idea. I should do something like that."

Well I finally did. Going to be sending this out for order in the next day or two, hopefully get it back before Christmas and hopefully it will work the way I think it will :P It's a simple microntroller driving 18 LEDs that will run off a CR2032 battery, I'm planning to program in some neat light patterns.
Capture.JPG
 

Latest posts